3M 800af manual Special Set-Up Procedure, Drive Belt Height, Disassembly

Page 38

Special Set-Up Procedure

WARNING – Turn off electrical power and air supply and disconnect power

cord from electrical supply before beginning special set-up procedure. If power cord is not disconnected, severe injury to personnel could result.

Changing Drive Belt Height

The drive belt assemblies can be raised 50 mm

[2 inches] to provide better conveying of tall boxes.

This change increase the minimum box height that can be taped to 190 mm [7-1/4 inches].

DISASSEMBLY – Figure 6-1

1.Using the height adjustment crank, raise the upper taping head to its fully raised position.

2.Remove and retain the M6 x 16 flat head cap screw (A), special washer (B) and spacer (C) from the front and rear arm assembly pivots.

3.Lift drive belt assembly (D) up off the arm assembly pivots.

Note – Keep motor in vertical position to prevent gear oil from leaking out of motor.

REASSEMBLY – Figure 6-2

4.Reassemble the spacer (C) onto the front and rear arm assembly pivots first.

5.Install the belt drive assembly (D) onto the pivots and secure with special washers (B) and M6 x 16 flat head cap screws (A).

Note – Both drive belt assemblies must be installed at the same operating height.

Figure 6-1 – Drive Belt Height, Disassembly

Figure 6-2 – Drive Belt Height, Reassembly

33

Image 38

Contents AccuGlideTM Replacement Parts and Additional Manuals To Our CustomersTo Our Customers Table of Content 800af Adjustable Case Sealer TypeSection II AccuGlide STD 2 Inch Taping Heads 3M-Matic800af Adjustable Case Sealer, Type Intended UseContents 800af Adjustable Case Sealer Important Safeguards Knife Warning LabelMoving Flap Kicker Safety Instructions Label 13 Permissible Lift Area Label Operating Rate SpecificationsPower Requirements Tape Width Operating ConditionsTape Tape Roll DiameterBox Weight and Size Capacities Set-Up Recommendations Machine Dimensions MinimumMaximum Machine Set-Up Installation and Set-UpReceiving And Handling Installation and Set-Up Conveyor Systems Initial Start-Up of Case Sealer Pneumatic ConnectionOperation Case Sealer ComponentsControls, Valves and Switches Electrical On/Off Switch Main Air On/Off Valve/Pressure Regulator/Filter -3Indicator, Air Pressure Height Adjustment Crank, Upper Taping HeadWidth Adjustment Crank Top Flap Compression RollersSee Section II, Pages 7 Box Size Set-Up Operation Machine before operating Passing through machine to avoid injuryFeeding boxes to the machine 11 Box Size Set-UpOccur Box Sealing 13 Box Size Set-UpTurn machine On only when it is safe to do so Box JamsMaintenance LubricationDamage Drive Belt Replacement/Tension Adjustment Drive Belt ReplacementDrive Belt Tension Adjustment Top View Circuit Breaker Knife Replacement, Taping HeadEquipment damage Air Line Filter -5 Drive Belt Tension AdjustmentsTaping Head Adjustments -Refer to Section Damage Upper Taping Head Leveling Gate Stroke Setting This page is Blank Special Set-Up Procedure Drive Belt Height, DisassemblyTaping Heads Outer Column Re-Positioning Refer to Figure Column Re-Positioning Troubleshooting Troubleshooting Guide Problem Cause CorrectionTroubleshooting Pneumatic Diagram Pneumatic DiagramElectrical Diagram Electrical DiagramPage This page is Blank Spare and Miscellaneous Parts Options/Accessories Part Number Option/AccessoryReplacement Parts Illustrations and Parts Lists This page is Blank 800af Adjustable Case Sealer Frame Assemblies 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 1of Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Ref. No 3M Part No Description 800af Adjustable Case Sealer Safety and Information Labels Ref. No 3M Part No Description Qty