Zebra Technologies LP 2844 manual Proprietary Statement

Page 3

Proprietary Statement

This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.

Product Improvements

Continuous improvement of products is a policy of Zebra Technologies Corporation. All specifications and signs are subject to change without notice.

FCC Compliance Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different than that to which the receiver is connected.

Consult the dealer or an experienced Radio/TV technician for help.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to insure compliance.

“The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate the equipment.”

Liability Disclaimer

Zebra Technologies Corporation takes steps to assure that its published Engineering specifications and Manuals are correct; however, errors do occur. Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.

No Liability for Consequential Damage

In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or the results of use of or inability to use such product, even ifZebra Technologies Corporation has been advised of the possibility of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you.

Trademarks

The Zebra logo and the zebra head design are both registered trademarks and LP 2844 is a service mark of ZIH Corp. Windows and MS-DOS are registered trademarks of Microsoft Corp. All marks are trademarks or registered trademarks of their respective holders.

Copyrights

This copyrighted manual and the label printer described herein are owned by Zebra Technologies Corporation. All rights are reserved. Unauthorized reproduction of this manual or the software in the label printer may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.

©2004 ZIH Corp. All rights reserved.

980483-001A

iii

Image 3
Contents Zebra LP 2844TM Desktop Printer 980483-001A Proprietary Statement Shock Hazard Contents Operation & Options 980483-001A Vii 980483-001A Hello IntroductionWhats in the Box? Opening the printer Inspecting the PrinterInspecting the Printer Closing the printer Reporting Damage Related DocumentationModes of Printing Getting StartedAttaching Power Supply Placing the Roll in the Media Compartment Loading Roll MediaAdjusting the Guides Status Light Power SwitchOperator Controls Feed ButtonMedia Length Sensing Interface Cable Requirements Hooking Up the Printer and ComputerSerial Interface Requirements USB Interface RequirementsParallel Interface Requirements Ethernet Interface RequirementsInternal ZebraNet PrintServer II Communications Communicating with the PrinterUniversal Serial Bus USB Communications Parallel CommunicationsSerial Communications CommandAdjusting the Print Quality Adjusting the Print Width980483-001A Thermal Printing Operation & OptionsReplacing Supplies Printing in Peel-Mode Printing on Fan-Fold Media Using the Cutter Option 980483-001A Cleaning MaintenanceCleaning Card Considerations Print Head ConsiderationsMedia Path Considerations Platen Considerations LubricationAssembly Replacing the PlatenRemoval Replacing the Print Head Removal Direct-Thermal LP ModelAssembly 980483-001A What the Status Light is Telling You TroubleshootingPrinter Operation Media Handling Printed image does not look right Print Quality ProblemsPrint head is under temperature No print on the labelLabel format was sent to, but not recognized by, the printer Manual Calibration Communications Diagnostics Resetting the Factory Default ValuesPrinter Condition Feed Button Action Feed Button ModesUniversal Serial Bus USB Connector AppendixInterfaces Host Parallel InterfaceZebraNet PrintServer II Internal Ethernet PrintServer Looking into the Printer’s RJ-45 Modular ConnectorSerial RS-232 Connector
Related manuals
Manual 54 pages 4.94 Kb