Panasonic CF-73 Series appendix List of Error Codes, To run the Setup Utility, Error Code/Message

Page 24

List of Error Codes

When turning on the computer, if one of the following error codes or messages is displayed, follow the instructions shown below. If the problem persists, or if the error code or message displayed is not shown here, contact Panasonic Technical Support. ( page 42)

Error Code/Message

0211: Keyboard error

0251: System CMOS checksum bad - Default configuration used

0271: Check date and time set- tings

0280: Previous boot incomplete - Default configuration used

0613: Serial Port*1 configura- tion changed

0614: Serial Port*1 config. error - device disabled

*1 The port name, such as A or B, is displayed, indicating the con- flicting ports.

Press <F2> to Setup

Operating System not found

Extended RAM Module Failed

Action

If an external keyboard or a mouse is connected, disconnect these devices.

An error has occurred in the memory that stores the Setup Utility settings. This error occurs when the memory content is changed through some inadvertent operation by a program or other function.

Run the Setup Utility and load the default values, then change the settings to the appro- priate values as needed.

If the problem persists, the internal clock battery may need to be replaced. Contact Pana- sonic Technical Support.

The date and time setting are incorrect.

Run the Setup Utility and set the date and time correctly.

If the problem persists, the internal clock battery may need to be replaced. Contact Pana- sonic Technical Support.

Startup has failed repeatedly, so the Setup Utility settings have been returned to their default values, and the computer has been booted.

Run the Setup Utility and load the default values, then change the settings to the appropri- ate values as needed.

I/O address and IRQ settings are in conflict.

Run the Setup Utility and change the settings in [Advanced] menu so there is no port conflicts.

Write down the error details and press F2 to run the Setup Utility. Confirm the settings, and change the settings to the appropriate values as needed.

The OS is not properly installed on the floppy disk or the hard disk that you are trying to boot from.

If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and use another bootable disk if not.

If the computer cannot be booted from the hard disk, confirm whether the hard disk is properly recognized in [Information] menu of the Setup Utility.

•If the hard disk is recognized, perform the reinstallation procedure.

•If not, contact Panasonic Technical Support.

If a device is connected to the USB port, disconnect the device, or run the Setup Utility and set [Legacy USB Support] in [Advanced] menu to [Disable].

If the extended RAM module has not been inserted properly, or if an extended RAM module other than one matching the specifications has been inserted, a beep will sound and the message “Extended RAM Module Failed” will be displayed when turning the power on. In this case, turn the power off, confirm that the extended RAM module meets the specifications, and reinsert it.

To run the Setup Utility

1Restart the computer.

2 Press F2 while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operating Instructions Introduction Illustrations and Terminology in this ManualCopyright Disclaimer Trademarks EnterRead Me First For U.S.AFCC Regulation Notice for modem This equipment contains a FCC approved modemRead Me First For CanadaIndustry Canada IC Notice for modem For Europe Industry CanadaRF Exposure Warning For models with a CE mark on the bottom of the computerLithium Battery Information to the UserPrecautions CD/DVD Drive CautionUsage Precautions Battery Pack Names and Functions of Parts Names and Functions of Parts Turn the computer over and insert the battery pack First-time OperationConfirm the inclusion of all parts Read the Limited USE License AgreementConnect your computer to a power outlet Setup WindowsFirst-time Operation Open the displayWhen creating a new user account Create a new accountSecurity Center Resetting the password Information for Windows XPCalibrate the touchscreen This concludes the first-time use operation guidelinesLatch Power Indicator Power Switch Starting Up/Shutting DownStarting Up Situation ActionSetup Utility Starting Up/Shutting DownLog on to Windows Select your applicationShutting Down power off your computer To shut down using the keyboardWhen you leave the computer or interrupt your work To quickly resume computer operation after shutting downTouch Pad Work Surface Right Button Left ButtonFunction Operation Moving the Cursor Tapping/Clicking Tapping clickingReference Manual Reference Manual / Important TipsReference Manual Important TipsMaintenance Useful InformationUsage Environment HandlingWhat is Windows Security Center? Security Center/Antivirus ProtectionAreas excluding the display Windows Update Useful InformationComputer Viruses Saving Data on the Hard DiskWhen Using Peripheral Devices When Changing Hard Disk PartitionsWhen Disposing of or Transferring Ownership of This Device Wireless LAN only for models with wireless LANList of Error Codes To run the Setup UtilityError Code/Message Dealing with Problems Summary Starting UpDealing with Problems Summary Entering PasswordDisplay NumLkShutting Down Battery Indicator Reinstalling B’s Recorder/B’s CLiPTouch Pad / Touchscreen Fast User Switching Function SD Memory CardOthers Reinstalling Software Before ReinstallationReinstalling PreparingIf the following message appears, press R Changing the drive letterAbout Intel software products Etary rights in the productContrat de licence d’usage limité LicenceTermes, clauses et conditions Hard Disk Backup Function Before Using a Hard Disk Backup FunctionPreparing Create a Backup Area Hard Disk Backup Function Backing Up and Restoring DataAt the confirmation message, select Yes and press Enter To disable the hard disk backup function Procedure Hard Disk Data Erase UtilitySpecifications Main SpecificationsSpecifications Wireless LAN only for models with wireless LANSoftware Operating SystemLimited Warranty Panasonic Computer and Peripherals Limited Warranty Panasonic Computer Solutions Company Panasonic Canada Inc
Top Page Image Contents