Panasonic CF-71 manual List of Error Codes, Code Description

Page 42

List of Error Codes

42

If a problem occurs with your hardware, and [POST Startup Error(s)] is displayed along with the error code(s), follow the on-screen instructions.

Setup: Setup Utility ( page 34) is started. Run [Load Default Settings (PnP)]. Rerun the Setup Utility to input the appropriate operating environment set- tings.

Exit: Ignore the error message(s), and restart the computer.

Code		Description

062	Boot failure--default configuration used	Default configuration in use
101	System Board Failure	Interrupt controller failure
102	System Board Failure	Timer 2 test failure
106	System Board Failure	Diskette controller failure
114	Adapter ROM Error	Adapter ROM checksum error
151	System Board Failure	Real-time clock failure
161	Bad CMOS Battery	Dead battery
162	Configuration Change Has Occurred	Configuration error
162	Configuration Error	CMOS checksum error
163	Date and Time Incorrect	Real-time clock is not updating
173	Configuration Change Has Occurred	ROM configuration has changed
201	Memory Size Error	Memory size/data error
301	Keyboard Error	Keyboard failure
303	Keyboard Error	Keyboard controller failure
604	Diskette Drive Error	Diskette drive 0 failure
605	Diskette Drive Error	Diskette unlocked problem
1780	Hard Disk Error	Fixed disk 0 failure
1800	PCI Error	No more IRQs available
1801	PCI Error	No more room for optional ROM
1802	PCI Error	No more I/O space available
1803	PCI Error	No more memory (above 1 MB) available
1804	PCI Error	No more memory (below 1 MB) available
1805	PCI Error	Checksum error or 0 size optional ROM
1962		An operating system could not be found
8603	Pointing Device Error	Pointing device failure
I9990301		Hard disk failure
I9990305		An operating system could not be found

Image 42

Contents Contents Reference Manual CF-71 SeriesKey Combinations Key Functions Popup WindowLED Indicators Determine the position to begin drawing Panasonic Hand Writing Touch PadDrawing Characters or Figures To nextClose the Hand Writing mode Panasonic Hand Writing Touch PadSelect Save As or Save from File Suspend/Hibernation Functions Setting the Suspend or Hibernation FunctionShutting Down Using the Suspend or Hibernation Function Starting Up Your Computer QuicklyPush the sleep switch or Slide the power switch Suspend/Hibernation FunctionsResuming Operation Precautions for Using the Suspend or Hibernation Function Security Measures When the User Password is setSetting the user password enabling, changing, disabling Situation Function to use ReferenceWhen the coffee break password is set To disable your passwordRe-enter your password at the Enter User Password Again Security MeasuresSetting the Coffee break Password enabling or disabling To disable the Coffee break PasswordRun the Setup Utility Using Preventing theft of damage to data using a floppy diskProcedure When the supervisor password is setSetting the Supervisor Password To disable your supervisor passwordEnabling, changing, disabling Conserving Power Computing On the RoadThings to Remember How to set Advanced and the suspend/hibernation timeout Setting Power ManagementHibernation with Using Computing On the RoadPower Management settings Use the Battery Indicator to Check on the Battery Status Battery PowerBattery Status Fn + F9Save your data and power off your computer Battery PowerWhen the Remaining Battery Charge Becomes Low If the suspend or hibernation function is setOpen the display Replacing the Battery PackRemove the battery pack Open the coverWhen closing the cover Connect the battery packConnector Tab Label-side up Flat Cable Close the coverUsing a Multimedia Pocket Device Installing/Removing a Multimedia Pocket DeviceParallel Port Using a Multimedia Pocket DeviceUsing the Floppy Disk Drive as an External Drive FDD CableInstalling a PC Card Using PC CardsInstalling/Removing the PC Card PC CardInstalling only if the ZV card does not operate properly Using PC CardUninstalling PC Card Utility ProgramInstalling/Removing the RAM Module Adding MemoryRAM Module Port Replicator Using a Printer External Display Port Using an External DisplayConnect the external display to your computer + F3Using USB Devices Run the Setup Utility Using EnterUsing USB Devices USB PortPreparations for Infrared Data Communications Setting for Infrared Data CommunicationsInfrared Data Communications Data CommunicationsInstalling/Removing the hard disk Removing/Installing the hard diskHard Disk Drive Connector Hard disk DriveRibs Closing the Program Setup UtilityRunning the Setup Utility Main ScreenSetup Utility System SetupParameters Power Management Power Management SettingsSupervisor Setup WSS Codec I/OIRQ Technical Information NetworkSome software will not run normally Technical InformationHard Disk Non-recognition from other operating systemsIt takes a long time to reboot or the computer locks up ReinstallationPower Saving Function in the Sound Chip System module error occursList of Error Codes Code DescriptionDMI Viewer Running DMI ViewerSaving information to a file Dealing With Problems Battery IndicatorStarting Up Dealing With Problems DisplayDisk Operations Character Input Application SoftwareNetwork Connecting Peripherals Copyright Disclaimer Trademarks