Panasonic CF-M34, CF-17 manual List of Error Codes, Failure Fixed Disk

Page 48

List of Error Codes

4 8

The following is a list of the messages that BIOS can display. Most of them occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured. Following the list are explanations of the messages and remedies for reported problems.

If your system displays one of except the messages marked below with an asterisk (*), write down the message and contact Panasonic Technical Support. If your system fails after you make changes in the Setup menus, reset the computer, enter Setup and install Setup defaults or correct the error.

0200 Failure Fixed Disk

Fixed disk in not working or not configured properly. Check to see if fixed disk is attached properly. Run Setup. Find out if the fixed-disk type is correctly identified.

0210 Stuck key

Stuck key on keyboard.

0211 Keyboard error

Keyboard not working.

0212 Keyboard Controller Failed

Keyboard controller failed test. May require replacing keyboard controller.

0213 Keyboard locked - Unlock key switch

Unlock the system to proceed.

0230 Shadow RAM Failed at offset : nnnn

Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.

0231 System RAM Failed at offset : nnnn

System RAM failed at offset nnnn of in the 64k block at which the error was detected.

0232 Extended RAM Failed at offset : nnnn

Extended memory not working or not configured properly at offset nnnn.

0250 System battery is dead - Replace and run SETUP

The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup to reconfigure the

system .

*0251 System CMOS checksum bad - Default configuration used

System CMOS has been corrupted or modified incorrectly, perhaps by an application program that changes data stored in CMOS. The BIOS installed Default SETUP Values. If you do not want these values, enter Setup and enter

your own values. If the error persists, check the system battery or contact Panasonic Technical Support.

0260 System timer error

The timer test failed. Requires repair of system board.

0270 Real time clock error

Real-time clock fails BIOS test. May require board repair.

*0280 Previous boot incomplete - Default configuration used

Previous POST did not complete successfully. POST loads default values and offers to run Setup. If the failure was caused by incorrect values and they are not corrected, the next boot will likely fail. On systems with control of wait states, improper Setup settings can also terminate POST and cause this error on the next boot. Run Setup and verify

that the wait-state configuration is correct. This error is cleared the next time the system is booted.

0281 Memory Size found by POST differed from CMOS

Memory size found by POST differed from CMOS.

02B0 Diskette drive A error

02B1 Diskette drive B error

Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that the drive is defined with the proper

diskette type in Setup and that the diskette drive is attached correctly.

02B2 Incorrect Drive A type - run SETUP

Type of floppy drive A: not correctly identified in Setup.

02B3 Incorrect Drive B type - run SETUP

Type of floppy drive B: not correctly identified in Setup.

02D0 System cache error - Cache disabled

Contact Panasonic Technical Support.

02F0: CPU ID:

CPU socket number for Multi-Processor error.

02F4: EISA CMOS not writable

ServerBIOS2 test error: Cannot write to EISA CMOS.

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Reference Manual CF-M34/CF-17 Series Illustrations in this Reference ManualRead Me First Saving Data on the Hard DiskSaving Data on Disks Computer VirusesMaintenance Read Me FirstUsage Environment HandlingKey Combinations N c t i o n s Popup WindowLED Indicators Using the Touch Pad Changing the mode of the touch padTouch Pad Advaced Touch Pad Advanced Basic OperationMagnify/reduce the display Handling the Touch Pad Touchscreen Handling the TouchscreenMoving the cursor Clicking Double-clicking DraggingConfiguring the Touchscreen TouchscreenMake necessary changes Click OK Panasonic Hand Writing Touchscreen Drawing Characters or FiguresSelect Save As or Save from File Setting the Suspend or Hibernation Function Shutting Down Using the Suspend or Hibernation FunctionSuspend/Hibernation Functions Starting Up Your Computer QuicklySuspend/Hibernation Functions Resuming OperationPrecautions for Using the Suspend or Hibernation Function Starting up when the password is set If entering the Setup Utility with Supervisor PasswordIf entering the Setup Utility with User Password Security MeasuresSetting the Supervisor Password Security MeasuresRun the Setup Utility Conserving Power Computing On The RoadThings to Remember Setting Timeout Function Computing On The RoadBattery Power Battery StatusUse the Battery Indicator to check the battery status Fn + F9Battery Power When the remaining battery charge becomes lowSave your data and power off your computer If the suspend or hibernation function is setPanasonic Battery Monitor Click DetailAccurately Displaying Battery Capacity Attach the battery pack, then connect the AC adapterReplacing the Battery Pack Remove the battery packRemove the cover Put the battery pack Put the cover back into placeInstalling/Removing the PC Card Installing a PC CardPC Cards Removing a PC CardInstalling/Removing the RAM Module RAM ModuleExternal Display Connect the external display to your computerTurn on the external display, then turn on your computer Installing USB Devices Set the power management function to disableInstall the Windows 95 USB device drivers USB DevicesUSB Devices Removing USB DevicesConnecting to a telephone line and settings Connecting a telephone line to the internal modemPerforming the Country setting for the modem D e mPort Replicator Accessories HandleHand-grip Belt and Shoulder Strap Installing/Removing the hard disk Hard Disk DriveInstalling the hard disk Put the cover back into place and insert the battery packHard Disk Drive Remove the hard diskSetup Utility Running the Setup UtilitySetup Utility Main MenuR a m e t e r s R a m e t e r s Default Advanced MenuSecurity Menu Power Menu Exit Menu R a m e t e r sSmart Boot Select Start Programs Panasonic Smart BootAdd check mark depending on your needs Click OK Technical Information T w o r kInternet Explorer DMI Viewer Running DMI ViewerSaving information to a file Creating Backup Disks Connect the external floppy disk drive to your computerCreating Backup Disks Make a copy of the CD-ROM driverSet the floppy disk to the write-protect state List of Error Codes Failure Fixed DiskList of Error Codes Allocation Error for deviceDealing With Problems Advanced Battery IndicatorStarting Up Shutting DownDealing With Problems Advanced DisplayReference Manual Drive Operations Timeout Function Character InputApplication Software SoundConnecting Peripherals P y r i g h t S c l a i m e r A d e m a r k s
Top Page Image Contents