Panasonic PT-AE3000U manual Installation, Sleep, High Altitude Mode, Lamp Power, Lamp Runtime

Page 44

OPTION menu

INSTALLATION

When installing the projector, select the projection method according to the projector position. Press I H to cycle through the options. See “Projection method” on page 15.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting on the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting on the ceiling and

projecting from rear

 

 

 

SLEEP

You can select the required duration of time and set the off timer to turn off the power of the projector automatically. 3 minutes before turn-off, the countdown of minutes will be displayed in the lower right corner. Press I H to cycle through the options.

OFF

 

 

240MIN.

 

 

 

 

 

 

HIGH ALTITUDE MODE

If you use the projector at high elevation, the HIGH ALTITUDE MODE setting need to be ON to set the fan speed high. Press I H to select the required option.

OFF

The fan speed is low.

ON

The fan speed is high.

NOTE:

•At 1 400 - 2 700 m (4 593 - 8 858 ft) above sea level, the setting must be ON.

•The loudness of fan noise depends on the HIGH ALTITUDE MODE setting.

LAMP POWER

You can adjust the power of the lamp to save on electricity, prolong the lamp life and reduce the noise.

Options

Function

 

 

NORMAL

When higher luminance is

required.

 

 

 

ECO-MODE

When lower luminance is

sufficient.

 

 

 

60MIN.

90MIN.

120MIN.

210MIN.

180MIN.

150MIN.

NOTE:

•When no input signal is detected, the function is disabled.

LAMP RUNTIME

You can check how long the lamp has been used.

Settings

NOTE:

•LAMP RUNTIME is a relevant matter for lamp replacement timing. See “Replacing the lamp unit” on page 47.

44 - ENGLISH

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Operating Instructions Important Safety Notice Dear Panasonic CustomerImportant Safety Notice Declaration of ConformityModel Number PT-AE3000U Trade Name PanasonicContents Contents Menu NavigationPicture menu Lens ControlPrecautions with regard to safety Do not look into the lens while the projector is being used Precautions with regard to safetyDo not set up the projector outdoors Remove the used batteries from the remote control promptly Do not put your weight on this projectorUse only the specified batteries Do not mix old and new batteriesProjector may be subject to electromagnetic interference Order to get the best picture qualityDo not touch the surfaces of the lens with your bare hands Liquid crystal panelAccessories Remote control for Safety cable Lens coverPower cord Power cord secure lockRemote control About Your ProjectorTop and front view Projector bodyAbout Your Projector About Your Projector Back and bottom view ComputerHdmi ComponentScreen size and throw distance Setting upCalculation methods for screen dimensions Front leg adjusters and throwing angle Setting upProjection method Mounting on the ceiling and projecting from frontAdjusting the lens shift dials Lens shift and positioningHorizontal shift Vertical shiftSetting up Projector location range When the screen position is fixedWhen the projector position is fixed 100%Before connecting to the projector Connecting example Component IN/S-VIDEOConnecting example Hdmi IN/COMPUTER ConnectionsSwitching the projector on/off Power cordConnecting Connect the power cord to a wall outletPower indicator informs you the status of the power Power indicatorSwitching the projector on/off Press the power or Enter button Switching on the projectorSwitching off the projector Selecting the input signal Switch on the connected devicesAdjust the focus and the projected image size Projecting an imageRemote control operation Managing the lens control settingsSwitching the picture mode Adjusting the imageLoading a saved setting Switching the aspect ratioAdjusting the signal condition with a waveform Remote control operationAdjustment example Adjusting with luminance optionsAdjusting with RGB options Contrast G/CONTRAST BSetting your own color profile Adjusting the selected colorCreate a new profile Managing stored logsSaving a log setting as a profile Deleting the saved profilesChanging the profile names Loading saved profilesResetting to the factory default settings Switching the input signalUsing the assigned function as shortcut Capturing an imageAdjusting with the bar scale items Menu NavigationNavigating through the Menu Displaying the main menuMain menu and sub-menu Menu NavigationLanguage Lens Control Picture menu Color Temperature Split AdjustDynamic Iris Waveform MonitorAdjusting the image in a split window NR Noise ReductionColor Standard xvYCCSignal Mode Memory SaveMemory Load Memory EditClock Phase Position menuPosition DOT ClockComponent signals Position menu Aspect ratio options and projection exampleZoom FITAuto Setup WSSOver Scan KeystoneAdjust ZOOM/FOCUS, H-AREA Position ZOOM/FOCUSLens Memory Load Lens Memory SaveYou can edit named lens memory settings Lens Memory EditArea Position Select Lens Memory Name Change and press the Enter buttonUnderlined item is factory default setting ButtonBlank function Assignable functionsOption menu Installation High Altitude ModeLamp Power SleepTemp and Lamp Indicators Managing the indicated problemsLamp indicator Temp indicatorCare and Replacement Cleaning the projectorCare and Replacement When to replace the lamp unitReplacing the lamp unit Before replacing the lamp unitAttaching the top cover Care and Replacement Removing and replacing the lamp unitResetting the Lamp Runtime Troubleshooting List of compatible signals Technical InformationQuality *2 Dots *1 MHz KHzSerial terminal Technical Information Communication settings Control commandsInquiry commands Specifications Video ComputerComponent HdmiLoop twice Loop once Ceiling mount bracket safeguardsInstalling the safety cable Unit mm DimensionsTrademark acknowledgements Index Index
Related manuals
Manual 60 pages 38.77 Kb
Top Page Image Contents