Option settings
Press the F or G button to select an item, and then press the I or H button to change the setting.
| OPTION |
| ||
OSD |
|
|
| ON |
|
|
|
|
|
NR |
|
|
| ON |
|
|
|
| |
CINEMA REALITY | ON | |||
|
|
|
|
|
BACK | COLOUR | BLUE | ||
|
|
|
|
|
WSS |
|
|
| ON |
|
|
|
| |
FRONT/REAR | FRONT | |||
|
|
|
| |
DESK/CEILING | DESK | |||
|
|
|
|
|
FAN | CONTROL | NORMAL | ||
|
|
|
|
|
LAMP | POWER | HIGH | ||
|
|
| ||
LAMP | RUNTIME | 5H | ||
SELECT |
| ADJ | ESC | |
| ||||
OSD
OSDON
[
OFF
ON
The signal name is displayed in the
OFF
Use this setting when you do not want the signal name to be displayed.
NOTE:
BThe setting for
Noise Reduction (NR)
NRON
[
OFF
If the signal is of such poor quality that picture interference appears, set “NR” to “ON”. To turn off the “NR” feature, set to “OFF”.
NOTE:
B“NR” cannot be set when HDMI signals are being input.
CINEMA REALITY
CINEMA REALITY 
ON
[
OFF
ON
Set to “ON” when you would like 24 frames per second pictures (such as movies) to project the source faithfully.
OFF
Set to “OFF” when the projected pictures have problems with captions or subtitles when the setting is “ON”.
BACK COLOUR
BACK COLOUR | BLUE |
| [ |
| BLACK |
This sets the colour which is projected onto the screen when no signal is being input to the projector.
WSS
WSSON
[
OFF
ON
When the device connected to SCART is turned on, the input select setting will be switched to SCART automatically, and “ASPECT” will also be set automatically.
When WSS (Wide Screen Signalling) is detected from PAL or 625i(576i) YPBPR signals, the aspect ratio will also be switched automatically.
OFF
When SCART signals are being input, the input select setting and “ASPECT” will not be set automatically.
WSS will not be detected from PAL or 625i(576i) YPBPR signals.
FRONT/REAR
FRONT/REAR 
FRONT
[
REAR
This setting should be changed in accordance with the projector
FRONT
When the projector is placed in front of a screen.
REAR
When using a translucent screen.
DESK/CEILING
DESK/CEILING 
DESK
[
CEILING
This setting should be changed in accordance with the projector
DESK
When the projector is placed on a desk or similar.
CEILING
When the projector is suspended from a ceiling using the ceiling bracket (sold separately).
FAN CONTROL
FAN CONTROL 
NORMAL
[
HIGH
Set “FAN CONTROL” to “HIGH”, when using this projector at high elevations (above 1 400 m) only.
LAMP POWER
LAMP POWER | HIGH |
| [ |
| LOW |
This setting changes the lamp brightness. When set to “LOW”, the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced.
The “LOW” setting is recommended for narrow rooms where a high picture luminance is not essential or for watching movies.
NOTE:
B“LAMP POWER” cannot be set when no signal is being input.
LAMP RUNTIME
This setting displays the usage time for the lamp unit which is currently being used. When replacing the lamp unit, follow the instructions on page 52, and reset “LAMP RUNTIME” to “0”.
NOTE:
BThe lamp’s operating life varies depending on the usage conditions (such as the “LAMP POWER” setting and the number of times the power is turned on and off).
Adjustments and settings