| LAMP indicator | |
| Displayed for 30 |
|
More than 2 700 hours* | seconds. Pressing any | Illuminates red during |
button will clear the | ||
| display. | image projection and |
| Remains displayed until | standby mode. |
More than 3 000 hours* |
| |
any button is pressed. |
|
* These periods of time may become shorter according to the settings of the projector.
Lamp unit replacement procedure
NOTE:
BIf the lamp usage time has passed 3 000 hours (when “LAMP POWER” has been set to “HIGH” and when “DYNAMIC IRIS” has been set to “ON”), the projector will switch to standby mode after approximately 30 minutes of operation. The steps ) to - on the next page should thus be completed within 30 minutes.
'Install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover fixing screws.
(Insert the mains plug into the mains socket and then press the MAIN POWER switch.
)Press the POWER button so that a picture is projected onto the screen.
*Press the MENU button to display the “MAIN MENU”, and then press the F or G button to select “OPTION”.
MENU
KEYSTONE
PICTURE
POSITION
SHUTTER
,Press and hold the ENTER button for approximately 3 seconds.
| OPTION |
|
OSD |
| ON |
|
|
|
NR |
| ON |
|
| |
CINEMA REALITY | ON | |
|
|
|
BACK | COLOUR | BLUE |
|
|
|
WSS |
| ON |
|
| |
FRONT/REAR | FRONT | |
|
| |
DESK/CEILING | DESK | |
|
|
|
FAN | CONTROL | NORMAL |
|
|
|
LAMP | POWER | HIGH |
|
| |
TIME | RESET [POWER OFF] | |
SELECT | ESC | |
The “LAMP RUNTIME” will change to “TIME RESET [POWER OFF]”.
BIf the MENU button is pressed, the lamp time resetting screen will be cancelled.
|
This will reset the cumulative |
#Turn off the MAIN POWER switch according to the procedure given in “Turning off the power” on page 26, and then disconnect the mains plug from the mains socket and check that the area around the lamp unit has cooled down.
$Use a Phillips screwdriver to turn the lamp unit cover fixing screws at the bottom of the projector, and then remove the lamp unit cover.
Lamp unit cover
Lamp unit cover fixing screws
%Use a Phillips screwdriver to loosen the two lamp unit fixing screws until the screws turn freely. Then hold the handle of the lamp unit and gently pull it out from the projector.
Lamp unit fixing screws
A
B
Handle
&Insert the new lamp unit while making sure that the direction of insertion is correct, and then use a Phillips screwdriver to securely tighten the lamp unit fixing screws.
When inserting the new lamp unit, be sure to push it in at the point A and B .
LANGUAGE
OPTION
SELECT 
ENTER 
EXIT
+Press the ENTER button to display the “OPTION” menu, and then press the F or G button to select “LAMP RUNTIME”.
| OPTION |
|
OSD |
| ON |
|
|
|
NR |
| ON |
|
| |
CINEMA REALITY | ON | |
|
|
|
BACK | COLOUR | BLUE |
|
|
|
WSS |
| ON |
|
| |
FRONT/REAR | FRONT | |
|
| |
DESK/CEILING | DESK | |
|
|
|
FAN | CONTROL | NORMAL |
|
|
|
LAMP | POWER | HIGH |
|
|
|
LAMP | RUNTIME | 2720H |
SELECT | ESC | |
usage time for the lamp unit to |
zero. |
Refer to page 26 for details on |
how to turn off the power. |
NOTE:
BBe sure to install the lamp unit and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on.
Care and maintenance