Panasonic PT-P1SDU operating instructions Cleaning and maintenance, Specifications

Page 32

Cleaning and maintenance

Before carrying out cleaning and maintenance, be sure to disconnect the power cord plug from the wall outlet.

Wipe the cabinet with a soft, dry cloth.

If the cabinet is particularly dirty, soak the cloth in water with a small amount of neutral detergent in it, squeeze the cloth very well, and then wipe the cabinet. After cleaning, wipe the cabinet dry with a dry cloth. If using a chemically-treated cloth, read the instructions supplied with the cloth before use.

Do not wipe the lens or the lens cover with a cloth that is dusty or which produces lint.

If any dust or lint gets onto the lens or the lens cover, such dust or lint will be magnified and projected onto the screen. Use a blower to clean any dust and lint from the lens and the lens cover surface, or use a soft cloth to wipe off any dust or lint.

Removing and attaching the lens cover

Removing

BTurn the ring to the right and remove the lens cover.

Attaching

BReplace the lens cover and turn it to the left to lock it in place.

NOTE:

BThe lens cover is made of glass, so dropping it or allowing it to hit hard objects may cause it to break. Be careful when handling the lens cover

BUse the projector with the lens cover attached.

Specifications

Power supply:

100 V - 240 V ~, 50 Hz/60 Hz

Power consumption:

180 W [During standby (when fan is

 

stopped): Approx. 3 W]

Amps:

2.2 A - 1.0 A

 

 

LCD panel:

 

Panel size (diagonal):

0.6 type (15.24 mm)

Aspect ratio:

4:3

Micro lens array:

Available

Display method:

3 transparent LCD panels (RGB)

Drive method:

Active matrix method

Pixels:

480 000 (800 x 600) x 3 panels

 

 

Lens:

Manual zoom (1.2 x) / Manual focus

 

F 1.7 - 1.8 f 17.0 mm - 20.4 mm

 

 

Lamp:

UHM lamp (130 W)

 

 

Luminosity:

1 500 lm

 

Scanning frequency (for RGB signals):

Horizontal scanning frequency:

15 kHz - 91 kHz

Vertical scanning frequency:

50 Hz - 85 Hz

Dot clock frequency:

Less than 100 MHz

YPBPR signals:

480i, 576i, 480p, 576p, 1 080/60i,

 

1 080/50i, 720/60p

Color system:

7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/

 

PAL60/SECAM)

 

 

Projection size:

965 mm - 7 620 mm (38˝ - 300˝)

 

 

Throw distance:

1.2 m - 9.9 m (3´11˝ - 32´5˝)

 

 

Optical axis shift:

4:1 (fixed)

 

 

Screen aspect ratio:

4:3

 

 

Installation:

Front/Rear/Ceiling/Desk (menu selection)

 

 

Speaker:

2.0 cm round x 1

Max. usable volume output:

0.5 W (mono)

 

 

Connectors

 

PC IN:

Single-line, D-sub HD 15-pin (female)

During RGB input:

0.7 V [p-p], 75 Ω

R.G.B.:

G.SYNC:

1.0 V [p-p], 75 Ω

HD/SYNC:

TTL, automatic positive/negative polarity

 

compatible

VD:

TTL, automatic positive/negative polarity

During YPBPR input:

compatible

1.0 V [p-p] (Including sync), 75 Ω

Y:

PB, PR :

0.7 V [p-p], 75 Ω

Others

62-ENGLISH

ENGLISH-63

Page 31 Page 33
Image 32
Page 31 Page 33
Contents LCD Projector Commercial Use Model No. PT-P1SDUDear Panasonic Customer PreparationDo not look into the lens while the projector is being used Declaration of ConformityContents Precautions with regard to safetyDo not handle the power cord plug with wet hands Insert the power cord plug securely into the wall outletDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorAccessories Insulate the battery using tape or similar before disposalDo not put your weight on this projector Do not place any heavy objects on top of the projectorBefore use Read this page first Other Setup menuLanguage Setup menu Front leg adjuster button # Connector panel $ Speaker Air outlet portLocation and function of each part Air inlet portRemote control unit Projector control panelSD operation buttons Setting-up Projection methodsProjector position Projection distancesConnections Connecting to computerConnecting to video equipment Preparation for the remote control unit Insert the battery holderTurning on the power Turning off the power #Press the Power button$Press the Power button again Direct power off functionAdjusting the volume Volume Turning off the picture and sound momentarily ShutterProjected ImageInserting and removing the SD memory card Playing back images from a SD Memory cardSD selection screen UsefulSetting a detailed playback method for the SD memory card Button functions during playbackInterval EffectAuto Play Main Menu On-screen menusMenu screens Returning a setting to the factory default Menu operation guideAdjusting the picture Picture ModeDetailed Setup DaylightviewAdjusting the position SettingsKeystone AspectOther settings Auto SignalPosition TV-SYSTEMChanging the display language Setting up the security function Amend PasswordSetup Inserted SD KEYLamp indicator Temp indicator RemedyReplacement procedure Lamp unit replacement periodCleaning Lamp unit replacement procedure Before calling for service Removing and attaching the lens cover Cleaning and maintenanceSpecifications List of compatible signals AppendixDCF standard Guide screen for computer connectionFolder directory name File nameUnits mm inch DimensionsProjection dimensions calculation methods Trademark acknowledgements FRANÇAIS-71 Précautions de sécurité AvertissementAvertissements AvertissementNe pas placer des récipients de liquide sur le projecteur Ne pas mettre d’objets étrangers dans le projecteurPendant un orage, ne pas toucher le projecteur ou le câble Ne pas obstruer les orifices d’entrée et de sortie d’airAvant l’utilisation Précaution à prendre lors du déplacement du projecteurAvertissements concernant l’installation Remplacement du bloc de lampe Période de remplacement du bloc de lampeMéthode de remplacement du bloc de lampe Remarque’écran R.A.Z. Compteur Lampe apparaît alors ’écran Coupe L’ALIMENTATION disparaît 5 secondes plus tard
Top Page Image Contents