Panasonic PT-L712NTE manual Specifications, PAL-N / Secam

Page 64

Specifications

Identical specifications appear in the separate PT-L712E Operating Instructions, but the following should be referred to for details on PT-L712NTE specifications.

Power supply:

100 V - 240 V ~, 50 Hz/60 Hz

Power consumption:

240 W Approx. 5 W - 10 W when in

 

 

standby mode (when fan is stopped)

Amps:

2.8 A - 1.0 A

LCD panel:

 

 

 

 

Panel size (diagonal):

0.9 type (22.86 mm)

Aspect ratio:

4:3 (16:9 compatible)

Micro lens array:

Available

 

 

Display method:

3 transparent LCD panels (RGB)

Drive method:

Active matrix method

Pixels:

786 432 (1024 x 768) x 3 panels

Lens:

Manual zoom (1 - 1.3) / focus lens

 

 

F 1.8 - 2.1, f 28.7 mm - 36.0 mm

Lamp:

UHM lamp (165 W)

Luminosity:

1600 lm/ANSI

Scanning frequency:

(for RGB signals)

 

 

Internal data (point scanning) method

 

Horizontal scanning frequency

 

24 kHz - 97 kHz

 

 

Vertical scanning frequency

 

50 Hz - 120 Hz

 

 

Dot clock frequency

 

 

135 MHz or less

 

YPBPR signals:

NTSC (480i), 480p, PAL (625i), 720p,

 

 

HDTV (1080i/1035i)

Colour system:

6 (NTSC / NTSC 4.43 / PAL / PAL-M /

 

 

PAL-N / SECAM)

Projection size:

762 mm - 7620 mm (30" - 300")

Throw distance:

1.1 m - 11.7 m (3'8" - 38'4")

Optical axis shift:

9:1 (fixed)

Screen aspect ratio:

4:3

 

 

 

Installation:

Front/Rear/Ceiling/Desk (Menu

 

 

selection method)

Speakers:

2.8 cm round x 2

Max. useable volume output:

2 W (1 W + 1 W) (stereo)

Connection terminals:

 

 

 

 

RGB/YPBPR IN:

Dual-line D-SUB HD 15-pin (female)

During YPBPR input:

 

 

 

 

 

Y:

1.0 V [p-p] (including sync signal),

 

PB,PR:

75 Ω

 

 

 

0.7 V [p-p], 75 Ω

 

 

-64-

 

 

 

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Operating Instructions LCD Projector Commercial UseContents Dear Panasonic Customer Safety PrecautionsDo not insert any foreign objects into the card slot Radio frequencies used by the wireless card Do not use the cards near other sources of radio emissionsAvailable channels EtsiCheck accessories Wireless card slotWireless card Names of each partWireless image transfer system for the projector System diagramTransferable images Main functions of the application software Software FunctionsExplanation of terms IP AddressSubnet Mask GatewayAd Hoc Mode Infrastructure ModeAccess Point ChannelJpeg PowerPoint ExifWireless function preparation Firstly, when using the wireless functionSetting procedure Setting exampleComputerProjectorComputer LAN Page Installing and removing the wireless card Inserting the wireless card# Turn off the power supply for the projector Close the slot cover$ Open the slot cover Press the eject switch Removing the wireless cardPush in the eject switch and then remove the wireless card On-screen menus List of menu screensProjector LAN settings LAN SetupLock Setup $ Mode ChannelSsid Subnet Mask KEY Installing and removing the computer’s wireless card Setting up the computer wireless cardInstalling the wireless card Removing the wireless card Installing the driverFor Windows Click OK without changing any of the detailed settings Click FinishClick Yes. The computer will then re-start Checking the protocol Click YesPage Click OK + Click Yes. The computer will then Re-start Page Installing the Configuration Utility Click CloseUsing the Wireless Manager Wireless Manager capabilitiesStarting and closing the Wireless Manager Displaying the Configuration UtilityComputer network settings Make the following settings # Select Setting $ Setting NameCreate DeleteWireless LAN ModeChecking communication with the projector Basic image transmission examples Example 2 Projecting already-existing imagesCapturing and transmitting computer screen images Before transmitting imagesFunctions of the Capture window Selecting the capturing method Close buttonArea capture Full Screen capture$ Right-click the icon on the taskbar, and select Capture Active Window capture Click Capture Start Select the window to be captured. NoteSetting the capturing conditions Transmitting existing images Functions in the Image List windowBasic operations Using Auto Play to play images in a specified order Image List status settings# Number of Loops $ IntervalOther useful Wireless Manager functions Shortcut Key AssignmentEncryption settings Using Jpeg Convertor What Jpeg Convertor can doStarting Jpeg Convertor Main screen functions+ Picture quality slider Save to SD Memory Card buttonMinimize button Maximize buttonQuality Importing files using drag-and-drop Images which cannot be importedChecking, sorting and deleting images Checking imagesSorting images Double click on the image you wish to checkConversion settings for saving images Deleting imagesSaving to other folders Save as different size check boxConverted size list box Picture quality sliderDCF standard Limits on directory namesFile names File formatUsing the Serial connector Before asking for serviceSymptom Check the following Message ListSymptom Check the following Symptom Check the following Specifications PAL-N / SecamSync Wireless card OptionsDimensions Trademark InformationMade in Japan S0801-2081C
Top Page Image Contents