Outlaw Audio 970 owner manual System Setup, Input Configuration, Exit Takes you out of Menu mode

Page 24

Owner’s Manual

System Setup

System Setup

At this point all of the necessary physical connections between the Model 970 and your source devices, display and speakers should be completed. All that remains is to properly configure the system to reflect your specific equipment and room characteristics.

Before starting the configuration process, make sure that all connections between the Model 970 and other system components are tight and secure Then turn on the Model 970 and your display device.

Note: When using the Remote Control during the configuration process, remember to first press the TNR button to control the Model 970.

To turn the Model 970 on:

1.Press the MASTER POWER ON/OFF button on the unit’s rear panel until it latches.

The Standby/On indicator on the front panel will glow amber.

2.Press the STANDBY button on the front panel, or any source selector button on the remote control.

The Standby/On indicator will turn green, and the front-panel display will illuminate.

3.Turn on your display device.

Make certain that it is set to the input for the jacks that are used to con- nect it to the Model 970, but do not select the DVI (or HDMI) input, as the Model 970’s menus are not visible through that type of connection.

4.Press the Menu button on the front panel or the remote control.

The Main menu will appear on-screen. You’ll also see an abbreviated ver- sion of the Main menu on the Model 970’s front panel display (FP3).

MAIN MENU

> INPUT

CONFIG

SPEAKER

SIZE

SPEAKER

X-OVER

SURROUND

CONFIG

CHANNEL

CALIBRATION

DELAY

ADJUST

SYSTEM

CONFIG

EXIT

 

Here’s a brief explanation of each item on the Main menu:

Input Config This menu enters the configuration settings for your Model 970’s inputs so that the desired audio source, surround mode, lip sync delay and other features are automatically put into use for each input when it is selected.

Speaker Size This menu tells your Model 970 where to route the bass frequen- cies to each speaker as best fits your system to give you the best bass reproduction without overdriving or possibly damaging your full-range speakers.

Speaker X-overThis menu selects the crossover points that direct bass fre- quencies to your subwoofer in line with the precise capabilities of the speakers at each position in your system.

Surround Config This menu lets you customize the parameters of the surround modes so that they match your needs and preferences.

Channel Calibration This menu sets the output level for each channel so the surround sound field accurately reproduces the source material.

Delay Adjust On this menu you enter the distance from each speaker to your viewing/listening position so that the Model 970 correctly delays sounds to each speaker as needed to make sure that they arrive at your ears when they should.

System Config This menu is where you enter general system-wide param- eters such as how long your on-screen display remains visible, volume control defaults, sleep timer settings, etc.

Exit Takes you out of Menu mode.

A NOTE ON SETUP MENUS AND THE FRONT PANEL DISPLAY: To make it easier to configure the Model 970 we suggest that you use a video display to view all the menu choices, but should you wish to set up your system with only the unit’s front panel display note that the top line of the display will always show what would be the top line of an on-screen menu display; the name of the menu or sub- menu in use. The bottom line of the display will change as you scroll through the available options to show the choices available in the menu being adjusted.

Input Configuration

This menu is where you start your system configuration, and for that reason it is the first item on the Main menu. Here is where you will tell the Model 970 which source components are connected to it so that the signals flow properly. You’ll also be able to customize each input by assigning a series of default values for surround modes and other parameters.

Video Input Configuration

We’ll start with the video inputs first. You may want to reference the Connection Record Chart you filled out when making connections to the Model 970.

To configure a Video input:

1.Turn on each of the sources you plan to use with the Model 970.

If you are using a DVD player, put a disc in and start it up.

2.Press the MENU button on the front panel or the remote to display the Main Menu.

The Main Menu appears on-screen:

MAIN MENU

> INPUT

CONFIG

SPEAKER

SIZE

SPEAKER

X-OVER

SURROUND

CONFIG

CHANNEL

CALIBRATION

DELAY

ADJUST

SYSTEM

CONFIG

EXIT

 

24

Outlaw Audio

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model When the power-supply cord or plug is damaged Please Read FirstPower Cord Handle the AC Power Cord GentlyWiring Installation LocationTable of Contents Outlaw Audio Model Brief Note On This ManualAccessories Activates or cancels the on-screen menuUnpacking Model 970 Front PanelAdjusts the volume level of the headphones Model 970 Front PanelSelects between AM or FM Selects between FM mono and FM stereoModel 970 Rear Panel Model 970 Rear Panel RP24 AC input seeRemote Control Model 970 Remote ControlThese buttons control the Model 970’s volume Other components begins the play functionOther components activates the recording function Other components temporarily stops Play or RecordSurround Formats Available Surround ModesModel 970 Front Panel and On Screen Display Dolby Digital Dolby Digital EXDolby Pro Logic Connecting Your Model Stereo Listening ModesConnection Record Chart Connecting Audio Components see Connecting Video Components see pagesVideo Recorder Digital TV Tuner/Cable Box/Satellite ReceiverVideo Display Connections AC power connection Antenna ConnectionsAmplifier Connections see Subwoofer Connection seeConnecting Audio Equipment to the Model Audio Recording DeviceConnecting a DVD Player to the Model DVD-Audio/SACD/DVD PlayerConnecting Other Video Components to the Model Audio Connection NoteConnecting a Video Display to the Model If the video display has an Hdmi inputConnecting an External Amplifier to the Model When using a passiveSystem Setup Input ConfigurationExit Takes you out of Menu mode Here’s a brief explanation of each item on the Main menuInput Configuration sub-menu appears DVD Configuration sub-menu will appearInput choices appear as follows as you scroll through them Speaker Placement Up to 200ms of delay can be selected in 10ms incrementsConfiguring Audio Inputs There is no Lip Sync Delay available for audio-only sourcesSpeaker Placement Left Front, Center, and Right Front SpeakersLeft and Right Surround Speakers Surround Back Left and Right SpeakersSpeaker Size Configuration To enter settings for speaker sizeSubwoofers Speaker Size sub-menu appearsSpeaker X-Over Crossover Configuration Select LB/RB when you have two Surround Back speakersTo enter settings for speaker crossover Speaker X-Over sub-menu appearsSurround Setting Configurations Surround Configuration sub-menu appearsNight Mode PanoramaDimension HP Headphone ModeChannel Calibration Channel Subwoofer OffsetChannel Calibration sub-menu appears Channel Calibration with the Model 970 Test ToneAs you desire Manual Channel Calibration with Your Own Test SourceDelay Adjust Delay Settings for Large RoomsTo set the Delay for each channel System Configuration Settings You can adjust the level from -70 to +10dBAvailable choices are Power Standby/On indicator on the front panel will glow amberModel 970 Operation Direct OperationUse this control to adjust the volume level Volume of the selected source will return at the new levelName of the selected source will reappear in the displays Night Mode Selection No Comp means no compression i.e., Night Mode OffSleep Timer Channel TrimUsing the AM/FM Tuner Lip-Synch DelayAdjusting Tone Controls Stereo will tune stereo signalsUsing Headphones Creating an AM or FM station-memory preset manuallyTo create FM station-memory presets automatically To select a preset stationRemote Control Setup and Operation Battery InstallationSetup Using Preprogrammed Codes To install batteries in the remote controlVolume Control Punch-Through LED will blink twiceYou can choose CBL, AUX, VCR, TV, SAT, CD, or AMP Care and Maintenance System ResetCleaning When You Are AwaySetup Codes TroubIeshootingDVD Players TV/VCR Combos VCRs Model 970 Specifications Outlaw Audio Limited Warranty T l a w a u d i o

970 specifications

Outlaw Audio's Model 970 is a high-performing preamp processor designed to meet the growing demands of home theater enthusiasts and audiophiles alike. With a focus on delivering an exceptional audio experience, the 970 integrates advanced features, cutting-edge technologies, and a user-friendly interface.

One of the standout features of the Outlaw 970 is its support for high-resolution audio formats. This preamp processor is equipped to handle various formats, including Dolby TrueHD and DTS-HD Master Audio, which ensures that soundtracks are reproduced with stunning clarity and detail. The device supports both multichannel audio and two-channel stereo, making it versatile for different listening environments.

Equipped with 7.1-channel processing, the Outlaw 970 provides an immersive sound experience that gives users the feeling of being right in the middle of the action. Additionally, it features a robust set of audio controls that allow users to tailor their auditory experience. The processor includes adjustable bass management, enabling seamless integration with various subwoofers, and multiple listening modes to suit various content, from music to movies.

In terms of connectivity, the 970 does not disappoint. It offers an array of inputs and outputs, ensuring compatibility with modern audio and video components. It features multiple HDMI inputs, coaxial and optical digital inputs, as well as analog audio inputs, providing flexibility for connecting different devices. An essential highlight is its acclaimed video processing, which ensures that users can enjoy high-quality video playback, supporting resolutions up to 4K.

The Outlaw 970 also incorporates advanced technologies such as room correction software designed to optimize audio performance based on the acoustics of your listening space. This calibration feature significantly enhances the clarity and coherence of sound, making it ideal for those looking to achieve audio perfection within their home theater setups.

With a user-friendly interface, the Outlaw 970 allows for easy navigation and configuration. The device comes with an intuitive remote control that provides quick access to essential functions, while its front panel offers a straightforward layout for manual adjustments.

In conclusion, the Outlaw Audio Model 970 stands as a premium choice for those seeking a preamp processor that combines high-performance audio processing, robust connectivity, and intelligent calibration technologies. Its dedication to quality audio reproduction and user adaptability makes it a valuable addition to any home theater system.
Top Page Image Contents