Outlaw Audio 970 Left Front, Center, and Right Front Speakers, Left and Right Surround Speakers

Page 27

Owner’s Manual

System Setup

Left Front, Center, and Right Front Speakers

Place them at the same relative height and, if at all possible, a bit away from any walls. Some acousticians recommend placement far away from any walls but that may not be practical in your situation.

Most speakers sound best with the tweeter positioned at “seated ear height”; the same height your ears are when you’re ready to watch and listen.

Take care to aim the speakers at your prime viewing/listening position. That will probably mean that the center channel speaker will be aimed straight ahead while the left and right speakers are “toed-in” a bit.

Left and Right Surround Speakers

Put these speakers about 3' (1 meter to you metric Outlaws) above your “seated ear height.”

Mount them on the side walls of your listening room, preferably a bit to the rear of the prime seating position, if possible. Different authorities have dif- ferent ideas here but, if the speakers are at the right height, you can vary their placement from slightly behind to slightly ahead of your prime viewing/ listening position.

If your surround speakers are dipolar rather than directional, remember to ori- ent the arrows on the dipole enclosures properly. For speakers on the side walls, point the arrows to the front of the room (i.e., towards the video display).

Surround Back Left and Right Speakers

Note: These speakers are required for Dolby Digital EX, DTS-ES, Dolby Pro Logic IIx, a nd 7-Channel Stereo. They are also desirable, though not required, for DTS Neo:6.

Put these speakers about 3’ (or 1 meter) above your “seated ear height.”

Place them on the rear wall, behind the prime viewing/listening position so that the angle between each speaker and the listener is approximately 30 degrees. If that’s confusing, try “dividing” the rear wall into thirds and placing the speakers at the 1/3 points on the back wall.

Dipoles placed on a rear or back wall should have the arrows pointing toward each other to achieve the correct acoustical image in the room.

If you’re using just one surround back speaker, center it directly behind your main viewing/listening area.

Speaker Placement

Model 970 7.1 Channel Preamplifier Processor

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model Please Read First When the power-supply cord or plug is damagedInstallation Location Power CordHandle the AC Power Cord Gently WiringTable of Contents Brief Note On This Manual Outlaw Audio ModelModel 970 Front Panel AccessoriesActivates or cancels the on-screen menu UnpackingSelects between FM mono and FM stereo Adjusts the volume level of the headphonesModel 970 Front Panel Selects between AM or FMModel 970 Rear Panel RP24 AC input see Model 970 Rear PanelOther components begins the play function Remote ControlModel 970 Remote Control These buttons control the Model 970’s volumeOther components temporarily stops Play or Record Other components activates the recording functionSurround Formats Available Surround ModesModel 970 Front Panel and On Screen Display Dolby Digital Dolby Digital EXDolby Pro Logic Stereo Listening Modes Connecting Your ModelConnection Record Chart Connecting Video Components see pages Connecting Audio Components seeVideo Recorder Digital TV Tuner/Cable Box/Satellite ReceiverVideo Display Connections Subwoofer Connection see AC power connectionAntenna Connections Amplifier Connections seeAudio Recording Device Connecting Audio Equipment to the ModelDVD-Audio/SACD/DVD Player Connecting a DVD Player to the ModelAudio Connection Note Connecting Other Video Components to the ModelIf the video display has an Hdmi input Connecting a Video Display to the ModelWhen using a passive Connecting an External Amplifier to the ModelHere’s a brief explanation of each item on the Main menu System SetupInput Configuration Exit Takes you out of Menu modeInput Configuration sub-menu appears DVD Configuration sub-menu will appearInput choices appear as follows as you scroll through them There is no Lip Sync Delay available for audio-only sources Speaker PlacementUp to 200ms of delay can be selected in 10ms increments Configuring Audio InputsSurround Back Left and Right Speakers Speaker PlacementLeft Front, Center, and Right Front Speakers Left and Right Surround SpeakersSpeaker Size sub-menu appears Speaker Size ConfigurationTo enter settings for speaker size SubwoofersSpeaker X-Over sub-menu appears Speaker X-Over Crossover ConfigurationSelect LB/RB when you have two Surround Back speakers To enter settings for speaker crossoverPanorama Surround Setting ConfigurationsSurround Configuration sub-menu appears Night ModeChannel Subwoofer Offset DimensionHP Headphone Mode Channel CalibrationManual Channel Calibration with Your Own Test Source Channel Calibration sub-menu appearsChannel Calibration with the Model 970 Test Tone As you desireDelay Adjust Delay Settings for Large RoomsTo set the Delay for each channel System Configuration Settings You can adjust the level from -70 to +10dBAvailable choices are Direct Operation PowerStandby/On indicator on the front panel will glow amber Model 970 OperationUse this control to adjust the volume level Volume of the selected source will return at the new levelName of the selected source will reappear in the displays Channel Trim Night Mode SelectionNo Comp means no compression i.e., Night Mode Off Sleep TimerStereo will tune stereo signals Using the AM/FM TunerLip-Synch Delay Adjusting Tone ControlsTo select a preset station Using HeadphonesCreating an AM or FM station-memory preset manually To create FM station-memory presets automaticallyTo install batteries in the remote control Remote Control Setup and OperationBattery Installation Setup Using Preprogrammed CodesVolume Control Punch-Through LED will blink twiceYou can choose CBL, AUX, VCR, TV, SAT, CD, or AMP When You Are Away Care and MaintenanceSystem Reset CleaningTroubIeshooting Setup CodesDVD Players TV/VCR Combos VCRs Model 970 Specifications T l a w a u d i o Outlaw Audio Limited Warranty

970 specifications

Outlaw Audio's Model 970 is a high-performing preamp processor designed to meet the growing demands of home theater enthusiasts and audiophiles alike. With a focus on delivering an exceptional audio experience, the 970 integrates advanced features, cutting-edge technologies, and a user-friendly interface.

One of the standout features of the Outlaw 970 is its support for high-resolution audio formats. This preamp processor is equipped to handle various formats, including Dolby TrueHD and DTS-HD Master Audio, which ensures that soundtracks are reproduced with stunning clarity and detail. The device supports both multichannel audio and two-channel stereo, making it versatile for different listening environments.

Equipped with 7.1-channel processing, the Outlaw 970 provides an immersive sound experience that gives users the feeling of being right in the middle of the action. Additionally, it features a robust set of audio controls that allow users to tailor their auditory experience. The processor includes adjustable bass management, enabling seamless integration with various subwoofers, and multiple listening modes to suit various content, from music to movies.

In terms of connectivity, the 970 does not disappoint. It offers an array of inputs and outputs, ensuring compatibility with modern audio and video components. It features multiple HDMI inputs, coaxial and optical digital inputs, as well as analog audio inputs, providing flexibility for connecting different devices. An essential highlight is its acclaimed video processing, which ensures that users can enjoy high-quality video playback, supporting resolutions up to 4K.

The Outlaw 970 also incorporates advanced technologies such as room correction software designed to optimize audio performance based on the acoustics of your listening space. This calibration feature significantly enhances the clarity and coherence of sound, making it ideal for those looking to achieve audio perfection within their home theater setups.

With a user-friendly interface, the Outlaw 970 allows for easy navigation and configuration. The device comes with an intuitive remote control that provides quick access to essential functions, while its front panel offers a straightforward layout for manual adjustments.

In conclusion, the Outlaw Audio Model 970 stands as a premium choice for those seeking a preamp processor that combines high-performance audio processing, robust connectivity, and intelligent calibration technologies. Its dedication to quality audio reproduction and user adaptability makes it a valuable addition to any home theater system.
Top Page Image Contents