Outlaw Audio 970 owner manual Channel Trim, Recording a Source, Night Mode Selection, Sleep Timer

Page 37

Channel Trim

Channel Trim allows you to fine-tune the channel levels to compensate for various soundtrack anomalies. For example, you may play a movie and find that the center (dialogue) channel sounds weak, making the movie hard to follow. Simply trimming the center channel up a decibel or two can fix the problem. Or another movie may have much more bass than normal; trimming the subwoofer channel down a few decibels should balance the sound correctly.

You can trim the channels while you are listening to a source, or you can trim the channels using the Model 970’s internal test tone. The trim range is +10dB to -10dB.

To adjust channel level while listening to a source:

1.Press TRIM on the remote control.

“TRIM LEVEL ADJUST” will appear in the front panel display and in the on-screen messages (unless you selected OSD: OFF in the Input Con- figuration menu). FRONT LEFT” will be the first channel to be shown on-screen and on the front-panel display along with the current channel output level offset.

2.Press the or buttons to adjust the level as desired.

3.When the desired level offset is set, use the and buttons to move through the list of channels.

Repeat steps 2 and 3 until you finished adjusting the channel levels.

4.Press SET when you are finished adjusting the channel outputs or wait a few seconds for the display to disappear.

To adjust channel level using the test tone, use the same procedure described above, except start the process by pressing the TEST button on the remote instead of the TRIM button. :

Recording a Source

You can record from any input source connected to the Model 970 when you have an audio or video recorder properly connected to the appropriate output jacks on the rear panel but you cannot monitor the output of the recorder through the Model 970 while recording.

To record from a currently selected analog input source:

1.Prepare your analog recording device.

Follow the recommended procedure from the recorder manufacturer about settings, etc.

2.Set the device to the record mode and begin recording.

The source audio signals appear at the Tape Record Outputs and the Video 1 audio outputs. If the source contains a video signal, it appears at both the composite and S-Video Record Outputs.

To record from a currently selected digital input source:

1.Prepare your digital recording device.

Follow the recommended procedure from the recorder manufacturer about settings, etc.

2.Set the device to the record mode and begin recording.

The source audio signals appear at the Coaxial and Optical Digital Audio Output jacks. If the source contains a video signal, it appears at both the composite and S-Video Record Outputs.

Owner’s Manual

Model 970 Operation

Notes on recording: You can record analog to analog and digi- tal to digital but you cannot record analog to digital or digital to analog through the Model 970.

If you change the input source during recording, you will record the signals from the newly selected input source from that point on.

Night Mode Selection

The Model 970’s Night Mode is intended for late-night listening. It suppresses the loud peaks in movie soundtracks and music videos so that the sound from your system does not disturb others. Yet you will still be able to play the system loud enough so you can hear dialogue clearly. Night Mode works only with Dolby Digital soundtracks.

You can activate Night Mode through the Surround Configuration sub-menu (see page 30) or directly from the remote control.

To adjust Night Mode from the remote control when a Dolby Digital source is playing:

1.Press the NIGHT button on the remote control.

The current setting of Night Mode appears on the front panel display and in the on-screen messages (unless you selected OSD: OFF in the Input Configuration menu.)

2.Press the NIGHT button to toggle between the two modes.

No Comp means no compression (i.e., Night Mode Off)

DR Comp means dynamic range compression (i.e., Night Mode On)

3.Press EXIT on the remote control to exit Night Mode selection, or wait a few seconds for the display to disappear.

Sleep Timer

The Model 970’s sleep timer automatically shuts the unit off after a predeter- mined amount of time. The sleep time can be activated through the System Configuration sub-menu (see page 35), or directly from the remote control.

To activate the sleep timer from the remote:

1.Press SLEEP on the remote.

“SLEEP TIME: 90 MIN” appears on the lower line of the front-panel

display and in the on-screen messages (unless you selected OSD: OFF in the Input Configuration menu.)

2.Press SLEEP repeatedly to reduce the amount of time before the Model 970 shuts off.

The available choices are:

90MIN75MIN60MIN45MIN30MIN20MIN10MIN5MINOFF

Choosing one of the time settings will cause the Model 970 to turn itself off after selected amount of time.

Choose OFF to disengage the sleep timer function

3.Press EXIT on the remote to remove the sleep timer display, or wait a few seconds for the display to disappear.

4.To check the amount of time left on the sleep timer, press SLEEP again.

Model 970 7.1 Channel Preamplifier Processor

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Model Please Read First When the power-supply cord or plug is damagedHandle the AC Power Cord Gently Power CordWiring Installation LocationTable of Contents Brief Note On This Manual Outlaw Audio ModelActivates or cancels the on-screen menu AccessoriesUnpacking Model 970 Front PanelModel 970 Front Panel Adjusts the volume level of the headphonesSelects between AM or FM Selects between FM mono and FM stereoModel 970 Rear Panel RP24 AC input see Model 970 Rear PanelModel 970 Remote Control Remote ControlThese buttons control the Model 970’s volume Other components begins the play functionOther components temporarily stops Play or Record Other components activates the recording functionAvailable Surround Modes Surround FormatsModel 970 Front Panel and On Screen Display Dolby Digital EX Dolby DigitalDolby Pro Logic Stereo Listening Modes Connecting Your ModelConnection Record Chart Connecting Video Components see pages Connecting Audio Components seeDigital TV Tuner/Cable Box/Satellite Receiver Video RecorderVideo Display Connections Antenna Connections AC power connectionAmplifier Connections see Subwoofer Connection seeAudio Recording Device Connecting Audio Equipment to the ModelDVD-Audio/SACD/DVD Player Connecting a DVD Player to the ModelAudio Connection Note Connecting Other Video Components to the ModelIf the video display has an Hdmi input Connecting a Video Display to the ModelWhen using a passive Connecting an External Amplifier to the ModelInput Configuration System SetupExit Takes you out of Menu mode Here’s a brief explanation of each item on the Main menuDVD Configuration sub-menu will appear Input Configuration sub-menu appearsInput choices appear as follows as you scroll through them Up to 200ms of delay can be selected in 10ms increments Speaker PlacementConfiguring Audio Inputs There is no Lip Sync Delay available for audio-only sourcesLeft Front, Center, and Right Front Speakers Speaker PlacementLeft and Right Surround Speakers Surround Back Left and Right SpeakersTo enter settings for speaker size Speaker Size ConfigurationSubwoofers Speaker Size sub-menu appearsSelect LB/RB when you have two Surround Back speakers Speaker X-Over Crossover ConfigurationTo enter settings for speaker crossover Speaker X-Over sub-menu appearsSurround Configuration sub-menu appears Surround Setting ConfigurationsNight Mode PanoramaHP Headphone Mode DimensionChannel Calibration Channel Subwoofer OffsetChannel Calibration with the Model 970 Test Tone Channel Calibration sub-menu appearsAs you desire Manual Channel Calibration with Your Own Test SourceDelay Settings for Large Rooms Delay AdjustTo set the Delay for each channel You can adjust the level from -70 to +10dB System Configuration SettingsAvailable choices are Standby/On indicator on the front panel will glow amber PowerModel 970 Operation Direct OperationVolume of the selected source will return at the new level Use this control to adjust the volume levelName of the selected source will reappear in the displays No Comp means no compression i.e., Night Mode Off Night Mode SelectionSleep Timer Channel TrimLip-Synch Delay Using the AM/FM TunerAdjusting Tone Controls Stereo will tune stereo signalsCreating an AM or FM station-memory preset manually Using HeadphonesTo create FM station-memory presets automatically To select a preset stationBattery Installation Remote Control Setup and OperationSetup Using Preprogrammed Codes To install batteries in the remote controlLED will blink twice Volume Control Punch-ThroughYou can choose CBL, AUX, VCR, TV, SAT, CD, or AMP System Reset Care and MaintenanceCleaning When You Are AwayTroubIeshooting Setup CodesDVD Players TV/VCR Combos VCRs Model 970 Specifications T l a w a u d i o Outlaw Audio Limited Warranty

970 specifications

Outlaw Audio's Model 970 is a high-performing preamp processor designed to meet the growing demands of home theater enthusiasts and audiophiles alike. With a focus on delivering an exceptional audio experience, the 970 integrates advanced features, cutting-edge technologies, and a user-friendly interface.

One of the standout features of the Outlaw 970 is its support for high-resolution audio formats. This preamp processor is equipped to handle various formats, including Dolby TrueHD and DTS-HD Master Audio, which ensures that soundtracks are reproduced with stunning clarity and detail. The device supports both multichannel audio and two-channel stereo, making it versatile for different listening environments.

Equipped with 7.1-channel processing, the Outlaw 970 provides an immersive sound experience that gives users the feeling of being right in the middle of the action. Additionally, it features a robust set of audio controls that allow users to tailor their auditory experience. The processor includes adjustable bass management, enabling seamless integration with various subwoofers, and multiple listening modes to suit various content, from music to movies.

In terms of connectivity, the 970 does not disappoint. It offers an array of inputs and outputs, ensuring compatibility with modern audio and video components. It features multiple HDMI inputs, coaxial and optical digital inputs, as well as analog audio inputs, providing flexibility for connecting different devices. An essential highlight is its acclaimed video processing, which ensures that users can enjoy high-quality video playback, supporting resolutions up to 4K.

The Outlaw 970 also incorporates advanced technologies such as room correction software designed to optimize audio performance based on the acoustics of your listening space. This calibration feature significantly enhances the clarity and coherence of sound, making it ideal for those looking to achieve audio perfection within their home theater setups.

With a user-friendly interface, the Outlaw 970 allows for easy navigation and configuration. The device comes with an intuitive remote control that provides quick access to essential functions, while its front panel offers a straightforward layout for manual adjustments.

In conclusion, the Outlaw Audio Model 970 stands as a premium choice for those seeking a preamp processor that combines high-performance audio processing, robust connectivity, and intelligent calibration technologies. Its dedication to quality audio reproduction and user adaptability makes it a valuable addition to any home theater system.
Top Page Image Contents