Argee MSA-004-004 quick start AC Power Cord and Cable Precautions, Electrical Safety Precautions

Page 21

AC Power Cord and Cable Precautions

Warning:

•The AC power cord for the server must be plugged into a grounded, power outlet.

•Do not modify or use a supplied AC power cord if it is not the exact type required in the region where the server will be installed and used. Replace the cord with the cor- rect type.

•Route the AC power cord and cables away from moving parts and foot traffic.

•Do not allow anything to rest on the AC power cord and cables.

•Never use the server if the AC power cord has been damaged.

•Always unplug the AC power cord before removing the unit for servicing.

Electrical Safety Precautions

Warning:

Heed the following safety precautions to protect yourself from harm and the server from damage:

CAUTION: Dangerous voltages associated with the 100-240 V AC power supply are present inside the unit. To avoid injury or electrical shock, do not touch exposed connections or components while the power is on.

•To prevent damage to the server, read the information in this document for selection of the proper input voltage.

•Do not wear rings or wristwatches when troubleshooting electrical circuits.

•To avoid fire hazard, use only the specified fuse(s) with the correct type number, volt- age, and current ratings. Only qualified service personnel should replace fuses.

•Qualified service personnel should be properly grounded when servicing the unit.

•Qualified service personnel should perform a safety check after any service is per- formed.

8e6 Threat Analysis Reporter Quick Start Guide

17

Image 21

Contents Guide 8e6 Enterprise Filter Quick Start Guide Contents 8e 6 Threat Analysis Reporter Quick Start Guide Threat Analysis Reporter Introduction Conventions Used in this Document About this DocumentProcedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Mount the Server Rack Setup PrecautionsRack Mount Instructions Optional Install the Chassis Rails8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Traditional UP Racks 8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Open Racks 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Install the Chassis into the Rack Power Supply Precautions Check the Power SupplyServer Operation and Maintenance Precautions General Safety InformationElectrical Safety Precautions AC Power Cord and Cable PrecautionsMotherboard Battery Precautions Step-by-Step Setup Procedures Initial Setup ProceduresStep-by-Step Setup Requirements Monitor and Keyboard SetupPortion of chassis rear Serial Console SetupHyperTerminal Setup Procedures 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Login screen, password prompts Step-by-Step Initial Setup Procedures#s3tup#r3k Configure Network Interface screen 8e6 Threat Analysis Reporter Quick Start Guide Configure Domain Name Servers screen Configure default gateway screenConfigure Host Name screen Time zone regional configuration screen Configure Wizard user screen Administration menu Setup Wizard Confirmation screenLog Off, Disconnect the Peripherals System Status ScreenBandwidth Management Physically Connect the Unit to the NetworkAccess the Threat Analysis Reporter Administrator Console Wizard Setup ProceduresLog in to the Threat Analysis Reporter Administrator Console Register administrator 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide R3000 Register R3000 & ER8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Specify Gauge Groups to be Monitored Register GaugesView, Edit Gauge Components Server Settings Conclusion LED Indicator Key Button Key LED Indicator Color Condition DescriptionMSA Units Declaration of the Manufacturer or Importer Safety ComplianceElectromagnetic Compatibility EMC Electromagnetic Compatibility Class a NoticeEC Declaration of Conformity Preliminary Setup Procedures Other Required Installation ItemsUnpack the Ethernet Tap Unit from the Box Install the Ethernet Tap Unit Ports in front panel of NetOptics 10/100BaseT Tap Index