Argee MSA-004-004 quick start Declaration of the Manufacturer or Importer, Safety Compliance

Page 53

Regulatory Specifications and Disclaimers

Declaration of the Manufacturer or Importer

Safety Compliance

	USA:	UL 60950-1 2nd ed. 2007
	Europe:	Low Voltage Directive (LVD) 2006/95/EC to CB Scheme EN 60950: 2006
	International:	UL/CB to IEC 60950-1:2006
Electromagnetic Compatibility (EMC)

	USA:	FCC CFR 47 Part 15, Verified Class A Limit
	Canada:	IC ICES-003 Class A Limit
	Europe:	EMC Directive, 2004/108/EC & Low Voltage Directive (LVD) 2006/95/EC

Federal Communications Commission (FCC) Class A Notice (USA)

This equipment has been tested and found to comply with the limits for a Class A digi- tal device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio fre- quency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Declaration of Conformity

Model: MSA-004-004

Electromagnetic Compatibility Class A Notice

Industry Canada Equipment Standard for Digital Equipment (ICES-003)

8e6 Threat Analysis Reporter Quick Start Guide

49

Image 53

Contents Guide 8e6 Enterprise Filter Quick Start Guide Contents 8e 6 Threat Analysis Reporter Quick Start Guide Threat Analysis Reporter Introduction Conventions Used in this Document About this Document8e6 Taiwan Procedures8e6 Corporate Headquarters USA Unpack the Unit from the Carton Select a Site for the Server Rack Mount the Server Rack Setup PrecautionsRack Mount Instructions Optional Install the Chassis Rails8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Traditional UP Racks 8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Open Racks 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Install the Chassis into the Rack Power Supply Precautions Check the Power SupplyServer Operation and Maintenance Precautions General Safety InformationElectrical Safety Precautions AC Power Cord and Cable PrecautionsMotherboard Battery Precautions Step-by-Step Setup Procedures Initial Setup ProceduresStep-by-Step Setup Requirements Monitor and Keyboard SetupPortion of chassis rear Serial Console SetupHyperTerminal Setup Procedures 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Login screen, password prompts Step-by-Step Initial Setup Procedures#s3tup#r3k Configure Network Interface screen 8e6 Threat Analysis Reporter Quick Start Guide Configure Domain Name Servers screen Configure default gateway screenConfigure Host Name screen Time zone regional configuration screen Configure Wizard user screen Administration menu Setup Wizard Confirmation screenLog Off, Disconnect the Peripherals System Status ScreenBandwidth Management Physically Connect the Unit to the NetworkAccess the Threat Analysis Reporter Administrator Console Wizard Setup ProceduresLog in to the Threat Analysis Reporter Administrator Console Register administrator 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide R3000 Register R3000 & ER8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Specify Gauge Groups to be Monitored Register GaugesView, Edit Gauge Components Server Settings Conclusion MSA Units LED Indicator Key Button KeyLED Indicator Color Condition Description Declaration of the Manufacturer or Importer Safety ComplianceElectromagnetic Compatibility EMC Electromagnetic Compatibility Class a NoticeEC Declaration of Conformity Unpack the Ethernet Tap Unit from the Box Preliminary Setup ProceduresOther Required Installation Items Install the Ethernet Tap Unit Ports in front panel of NetOptics 10/100BaseT Tap Index