Argee MSA-004-004 quick start About this Document, Conventions Used in this Document

Page 6

About this Document

This document is divided into the following sections:

•Introduction - This section is comprised of an overview of the Threat Analysis Re- porter product and how to use this document

•Service Information - This section provides 8e6 Technologies contact information

•Preliminary Setup Procedures - This section includes instructions on how to physi- cally set up the Threat Analysis Reporter unit in your network environment

•Install the Server - This section explains how to configure the Threat Analysis Re- porter

•Conclusion - This section indicates that the quick start steps have been completed

•LED Indicators and Buttons - This section explains how to read LED indicators and use LED buttons for troubleshooting the unit

•Regulatory Specifications and Disclaimers - This section cites safety and emis- sions compliance information for the TAR model referenced in this document

•Appendix: Optional Ethernet Tap Installation - This appendix explains how to install the optional Ethernet Tap device on your network for bandwidth monitoring

•Index - An alphabetized list of some topics included in this document

Conventions Used in this Document

The following icons are used throughout this document to call attention to important information pertaining to handling, operation, and maintenance of the server; safety and preservation of the equipment, and personal safety:

NOTE: The “note” icon is followed by additional information to be consid- ered.

WARNING: The “warning” icon is followed by information alerting you to a potential situation that may cause damage to property or equipment.

CAUTION: The “caution” icon is followed by information warning you that a situation has the potential to cause bodily harm or death.

8e6 Threat Analysis Reporter Quick Start Guide

Image 6

Contents Guide 8e6 Enterprise Filter Quick Start Guide Contents 8e 6 Threat Analysis Reporter Quick Start Guide Threat Analysis Reporter Introduction About this Document Conventions Used in this DocumentProcedures 8e6 Corporate Headquarters USA8e6 Taiwan Unpack the Unit from the Carton Select a Site for the Server Rack Setup Precautions Rack Mount the ServerOptional Install the Chassis Rails Rack Mount Instructions8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Traditional UP Racks 8e6 Threat Analysis Reporter Quick Start Guide Optional Install the Open Racks 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Install the Chassis into the Rack Check the Power Supply Power Supply PrecautionsGeneral Safety Information Server Operation and Maintenance PrecautionsAC Power Cord and Cable Precautions Electrical Safety PrecautionsMotherboard Battery Precautions Step-by-Step Setup Requirements Initial Setup ProceduresStep-by-Step Setup Procedures Monitor and Keyboard SetupSerial Console Setup Portion of chassis rearHyperTerminal Setup Procedures 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Step-by-Step Initial Setup Procedures Login screen, password prompts#s3tup#r3k Configure Network Interface screen 8e6 Threat Analysis Reporter Quick Start Guide Configure default gateway screen Configure Domain Name Servers screenConfigure Host Name screen Time zone regional configuration screen Configure Wizard user screen Setup Wizard Confirmation screen Administration menuSystem Status Screen Log Off, Disconnect the PeripheralsPhysically Connect the Unit to the Network Bandwidth ManagementWizard Setup Procedures Access the Threat Analysis Reporter Administrator ConsoleLog in to the Threat Analysis Reporter Administrator Console Register administrator 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Register R3000 & ER R30008e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide 8e6 Threat Analysis Reporter Quick Start Guide Register Gauges Specify Gauge Groups to be MonitoredView, Edit Gauge Components Server Settings Conclusion LED Indicator Key Button Key LED Indicator Color Condition DescriptionMSA Units Electromagnetic Compatibility EMC Safety ComplianceDeclaration of the Manufacturer or Importer Electromagnetic Compatibility Class a NoticeEC Declaration of Conformity Preliminary Setup Procedures Other Required Installation ItemsUnpack the Ethernet Tap Unit from the Box Install the Ethernet Tap Unit Ports in front panel of NetOptics 10/100BaseT Tap Index