3Com 5112M-TPLS installation and operation guide Unpacking Procedures

Page 40

Unpacking Procedures

To unpack your Security Module:

1.Verify that the Security Module is the correct module by matching the model number listed on the side of the shipping carton to the model number you ordered.

Note that the product model number printed on the shipping box differs from the model number on the product. The model number on the shipping box contains the prefix ’3C9’.

If the module appears to be damaged, return it to the anti-static shielding bag, repack it in the shipping carton, and contact your local 3Com supplier.

2.Remove the Security Module, in its anti-static bag, from the shipping carton.

3.Remove the module from the anti-static shielding bag and inspect it for damage. Save the package of screws in the carton; you will need them when you attach a cable to the module. Always handle the Security Module by the faceplate, being careful not to touch the components.

Keep the shipping carton and anti-static shielding bag in which your module was shipped in case you want to repackage the module for storage or shipment. Record the serial number of your Security Module. A log for information specific to your modules is provided under the Slot Usage Chart in Appendix B of the ONline System Concentrator Installation and Operation Guide.

3 - 4 ONline 10BASE-T Security Module Installation and Operation Guide

Image 40

Contents Page VDE Class B Compliance Restricted Rights Page Contents Installing and Operating the Module Troubleshooting Appendix B Technical Support Figures Page Tables Page How to Use This Guide AudienceStructure of This Guide Convention Indicates Example Document ConventionsUsr/snm/agents Related Documents 3Com Documents Reference DocumentsPage Introduction ONline 10BASE-T Security ModuleTheory of Operation ApplicationONline Management ONline 10BASE-T Security Module ApplicationPage Designing and Expanding the Network Understanding the General Rules Basic Network RulesSeven Basic Network Rules Rule Definition Recommendations/NotesCertain LAN devices Seven Basic Network Rules LAN Product Equivalent Distances LAN EquivalenceLAN Product Equivalent Fiber Fiber Backbone, Twisted Pair To-The-Desk Fiber Backbone, Twisted Pair To-The-Desk Example Sample Configuration Distance Calculation Maximum Link Distance on Twisted Pair Twisted Pair Backbone, Twisted Pair To-The-DeskCable Gauge Supports Link Distances Up To Patch Panels Unshielded Twisted Pair NetworkRedundant Twisted Pair Configuration Redundant LinksDesigning and Expanding the Network 2 Page Installing and Operating the Module Precautionary Procedures Quick Installation ChartProcedures for Completing Installation Step Procedure ReferenceInstalling the Module Unpacking Procedures Setting the Dip Switch Security Module Dip Switch SW1 LocationDIP Switch SW1 Network Selection Settings Switch Network Selection Switch SettingsSwitch Function Factory Setting DIP Switch SW1 Security and Link Integrity SettingsOff On Installing the Module Installing the Cable Tie-Wrap KitAttaching the Tie-Wrap Bracket to the Module Attaching Cables With 90 Connectors Installing the Module Installing an ONline 10BASE-T Security ModuleONline 10BASE-T Security Module Cable Connection Configuring the Module Network Assignment Port EnablePort Redundancy Link Integrity Module SecurityReverting Module Configurations Saving Module ConfigurationsAutopartition Threshold Showing Module Configurations Show Module Show Module Verbose Show Port Show Port VerboseMonitoring the Front Panel Security Module Faceplate Interpretation of the Security Module LEDs Color State Indicates NameLED and Network Verification LED State Network ConfigurationNetwork Check Codes Page Configuring Security Features Quick Reference for Configuring the Security Module Quick Reference for Configuring SecurityProcedure Command SET Security Autolearn Configuring Security Features Eavesdropping SecurityIntrusion Detection Example of Eavesdropping SecurityDefining Port Security Type Example of Intrusion DetectionDefining Port Action on Intrusion Configuring Autolearning Mask Enabling PortsConfiguring Autolearning Autolearn capture done learned 0 addresses total Defining a MAC Address Manually Downloading the Autolearning Database Configuring Security Mode Saving Security Configurations Showing Security ConfigurationsReverting Security Configurations Showing Port Configurations Eavesdrop None ETHERNET1 Showing Security Autolearn Showing Security Intruder List Clearing Security Configurations Clearing the MAC Address TableClearing the Autolearning Database Clearing the Security Intruder ListUsing 3Com MIB Security Variables EMM Security Snmp VariablesUsing the Security Module Snmp Variables Configuring Security Features 4 Page Troubleshooting TroubleshootingTroubleshooting Using the Status LEDs Troubleshooting Using the Port Status LEDsTroubleshooting Using the Port Status LEDs Troubleshooting Using the Activity LEDs Troubleshooting Using the Activity LEDsLED State Possible Problem Troubleshooting Solutions Technical Assistance Page Specifications Electrical SpecificationsMechanical Specifications Environmental SpecificationsGeneral Specifications Pin Connector and Cable Figure A-1 -Pin Cable Male and Female Connectors Table A-1 -Pin Cable Pinouts and Port Assignments Hub Trans CeiverPort # Function PolarityTwisted Pair Connectors and Cables Hub TransHub Port #Twisted Pair Connectors Figure A-2. RJ-45 Connector PinoutsTwisted Pair Cables Technical Support On-line Technical SupportEmail Technical Support Support from Your Network SupplierWorld Wide Web Site Support from 3Com Accessing the 3Com MIB Returning Products for Repair3Com Technical Publications Page Index Activity LEDs, 3-18,3-20 Quick Reference Chart Security Type Default Setting Index