TM-L90/TM-L90 with Peeler Technical Reference Guide

2.8.4 Operating procedure of Memory Switch Settings

The procedures used for this process are described below.

Entering Memory Switch Settings Mode

1.Open the roll paper cover, and turn on the power while pressing FEED inside the printer. You need to keep pressing the FEED button until the POWER, ERROR, and PAPER OUT LED come on.

2.While the POWER, ERROR, and PAPER OUT LEDs are on, press FEED inside the printer twice. 3.Close the cover.

The current setting and setting guidance will be printed automatically.

Selecting Items to Set

Open the roll paper cover.

Select setting items according to the number of times FEED is pressed, and close the roll paper cover.

Pressing the FEED button 0 times or 12 or more times will terminate this procedure.

1 time: Autocutter (TM-L90 only)

2 times: Paper/Print Density

3 times: Basic Serial Interface Settings

4 times: Advanced Interface Settings

6 times: Interface Reset Signal

7 times: Paper Width

8 times: Other Settings

9 times: FEED button operational settings (TM- L90 peeler specifications only)

11 times: Label Settings

No change for numbers other than at left

Selecting Individual Settings

Open the roll paper cover.

Press the FEED button the number of times required to select the setting for each item; then close the roll paper cover.

Autocutter(TM

-L90 only)

(page 2-28)

Selection of Paper and Print density

Selection of

Paper

(page 2-28)

Selection of Print

density

(page 2-28)

Serial

communication

condition

Baud Rate Setup

(page 2-29)

Data Length,

Handshake or Parity

(page 2-30)

Communication

 

 

 

FEED button

 

 

related

 

 

 

 

 

 

operational settings

 

 

Condition

 

 

 

 

 

(TM-L90 peeler

 

 

(page 2-30)

 

 

 

 

 

specifications only)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(page 2-33)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Other settings

 

 

Interface reset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Setting PAPER

 

 

 

signal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT LED

 

 

 

(page 2-31)

 

 

 

 

 

 

 

 

 

 

 

 

 

(page 2-32)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Paper layout

 

 

 

 

 

 

 

 

 

 

 

error recovery

 

 

 

 

 

 

 

 

 

 

 

methods

 

 

 

 

 

 

 

 

 

 

 

(page 2-32)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Label Settings

Maximal length of paper auto- measurement (page 2-34)

With or without the function of feeding paper to the print starting position at power on (page 2-34)

Ending Memory Switch Settings Mode

Turn the power off. The printer prints new settings and save the settings to the non-volatility memory. Then the software is reset and the printer enters the normal printable status. Turn the power off.

Rev. B

Setup 2-27

Page 51
Image 51
Epson L90 manual Operating procedure of Memory Switch Settings, Entering Memory Switch Settings Mode