DIP switch settings Serial interface model, Off | Epson L90 instruction

DIP switch settings (Serial interface model)

Switch No.	Function	ON			OFF

1	Enable/disable Power switch.	Switches power supply On/Off			Power supply switch is used to
		using commands. (Power			switch power On/Off.
		supply switch is disabled.)

2	Select for serial communication	Set using DIP switch			Set using memory switches.
	condition.	1-7, 1-8

3	Handshake	XON/XOFF			DTR/DSR

4	Bit length	7 bits			8 bits

5	Parity check	Yes			No

6	Parity type	Even			Odd

7	Baud rate (bps)	7	8
		ON	ON	:2400
8		ON	ON	:2400
8		OFF	ON	:4800
		OFF	ON	:4800
		ON	OFF	:9600
		OFF	OFF	:19200

bps: Indicates the number of bits transferred per second.

DIP switches 2 to 8 are for serial communication. Not used in parallel communication.

Note:

When using an OPOS or Advanced Printer Driver, do not change the DIP switch 1-1 from the OFF position (power supply switch enabled). The printer may not operate normally if the DIP switches are set to ON.

When you set the baud rate with the memory switch, you can set faster communication than with the DIP switch. (Refer to “Communication Condition” on page 2-29, “Error code” on page F-3)

In serial communication, intermittent printing* may occur. This is because when the communication speed is low, a data transmission waiting state occurs frequently since the printing mechanism speed is high. Increasing the communication speed may reduce this symptom.

* Intermittent printing: White streaks as large as one or two hairs appear horizontally in a printing result.

2-22 Setup

Rev. B

Image 46

Epson L90 manual DIP switch settings Serial interface model, Off

Contents

TM-L90/TM-L90 Peeler Technical Reference Guide Page Revision Table TM-L90/TM-L90 with Peeler Technical Reference Guide For Safety Key to Symbols Iii Modular Connector Aim of the Manual Manual ContentAbout This Manual Related Documentation Rev. B Contents Connecting to the Host Computer and Options Application Development Information Appendix a Interface And Connectors ESC/POS Command-Related InformationProduct Specifications Appendix B Consumable Specifications Appendix C Character Code Table Appendix F Troubleshooting Appendix D Option SpecificationsAppendix E Maintenance Appendix G Shipping ProceduresPage Product Structure AccessoriesProduct Overview Models Option 2Product Overview Rev. B Part Names TM-L90 Name and Description of Each PartPrinter Part Names Part Names of TM-L90 Peeler Specification Part names TM-L90 peeler specification4Product Overview Rev. B Control Panel Feed button with the TM-L90 peeler specificationFeed button with TM-L90 6Product Overview Rev. B Paper OUT LED with the TM-L90 peeler specification Power SwitchPaper OUT LED with TM-L90 Mode switch TM-L90 peeler specification only Power switch cover8Product Overview Rev. B Mode switch Connector Panel Connectors10Product Overview Rev. B Setup Setup Flow Precaution For Installation Installation Procedures2Setup Rev. B Instructions for Installation 4Setup Rev. B Paper exit guide With TM-L90 Adjusting Roll Paper Near-End Detection Position6Setup Rev. B Part names and the locations of N.E. detector components Rev. B Setup Adjustment Positions of N.E. Detector 8Setup Rev. BDetector Holder Load the roll paper Close the roll paper cover With the TM-L90 peeler specification Setup Rev. B Adjust the sensor so that it projects from the window Near end sensor adjustment position Near end sensor holder Set the roll paper Close the roll paper cover Connecting Power Supply Unit PS-180 Attaching Power Supply Unit Power Supply Connector Autocutter settings TM-L90 only Lift the top of the cutter unit upward and remove it Setup Rev. B Setting Roll Paper Width Notch Front edge Shaft Protrusion DIP Switch Settings DIP switch settings Serial interface model OFF Setting Memory Switches DIP switch settings Parallel, USB, Ethernet model Items that can be set in the memory switch setting mode Starting the Memory Switch Setting mode Location of the Feed button inside the roll paper cover Ending Memory Switch Setting mode Operating procedure of Memory Switch Settings Entering Memory Switch Settings Mode Selecting individual settings Selection of Print density Rev. B Setup Setup Rev. B Rev. B Setup Or more times No change With the TM-L90 peeler specification Setting Various Items via Utilities How to Set Various Items with ESC/POS Commands Memory Switch Functions TM-L90 memory switch settings MSW8 Customized values Serial Communication condition TM-L90 peeler specification memory switch settings MSW7 TM-L90/TM-L90 with Peeler Technical Reference Guide Serial Communication condition Paper Loading Method Paper setting with peeling issuing Rev. B Setup Setup Rev. B Setting Paper Layout Automatic paper layout setting Rev. B Setup +1.5 mm Parameters Calculated for Automatic Layout Setting Clearing Paper Layout Setting TM Setup Items Summary Feed Self Test Mode Operating Mode Panel Switch OperationWith TM-L90 With the TM-L90 peeler specification Connecting the Cable Connecting to the Host Computer and OptionsConnecting to the Host Computer and Options Connecting to the Host Computer With the RS-232C interface Direct Connection Stand alone Pass-through Connections Tightening Screws Connection procedureHexagon Bolts Threaded in Inches and Millimeters With the parallel IEEE1284 interface With the USB interface 6Connecting to the Host Computer and Options Attaching Locking Wire Saddle With the Ethernet interface IEEE802.3 TM-L90 only Names of parts Name of Parts Connecting to the Drawer 10Connecting to the Host Computer and Options Windows Driver Epson Advanced Printer Driver Application Development InformationIntroduction of Control Methods Epson Advanced Printer Driver Overview Epson Advanced Printer Driver Contents 2Application Development Information Rev. B Supported OSs with confirmation of system operation Epson Advanced Printer Driver Support EnvironmentSupported interfaces Supported development languages 4Application Development Information Rev. B Driver Information and Download Destination Epson Opos ADK Contents Epson Opos ADK Opos Control Overview 6Application Development Information Rev. B Epson Opos ADK Support Environment Various Utilities 3 ESC/POS CommandsTM Printer Memory Switch Setup Utility Electronic Logo Registration Utility for Nvram Printer Cover Sensor Sensors8Application Development Information Rev. B Busy state OfflineSelecting conditions that invoke a Busy State Receive buffer Label peeling sensor peeler specification only10Application Development Information Rev. B Printer Busy conditions and the Msw1-3 status Print Speed Setting of Paper WidthPrint Density Paper to use for high speed Code 128 Barcode Barcode Printing12Application Development Information Rev. B Printable characters for code set a 14Application Development Information Rev. B Printable characters for code set B Printable characters for code set C NV Memory Precautions for Two-Dimensional Code PrintingTwo-Color Printing 16Application Development Information Rev. B Corrective procedure FAQ ListConfirmation procedure Print data dropout occurs Check the handshake process 18Application Development Information Rev. B Rev. B Application Development Information 20Application Development Information Rev. B Power Supply Switch-Related User Operation List ESC/POS Command-Related InformationPower Off Control by the Host Head Divided Control When the Power Supply Switch is EnabledWhen the Power Supply Switch is Disabled Control After Paper Cut Using the NV Memory Printer initial setting upChanging command default values Customizing Printer Hexadecimal Dump Mode Printer Status Product Specifications Product SpecificationsTM-L90 2Product Specifications Rev. B TM-L90 peeler specification Print Specifications 4Product Specifications Rev. B Reliability Mtbf 6Product Specifications Rev. B TM-L90 peeler specification Character Specifications Character Specifications8Product Specifications Rev. B Character Configurations and Dimensions Precautions for Printing and Paper Feed Paper Feed SpecificationsPaper Specifications Paper feed Thermal Paper 10Product Specifications Rev. BPrinting Area Printable Area For Thermal Paper Label Printable Area for Label Printing Position in Relation to Cutter Position TM-L90 12Product Specifications Rev. BPrinting Position in Relation to Cutter Position 23.5mm 14Product Specifications Rev. B Overview of External DimensionsExternal Appearance TM-L90 External Appearance TM-L90 Peeler Specification Operating specifications 16Product Specifications Rev. B Interface board specifications RS-232 standard Interface And ConnectorsRS-232 Serial Interface Functions of each connector pin RTS 3 XON/XOFF Code IEEE1284 Parallel Interface Mode Interface Signals Connector Pin Assignment 6Interface And Connectors TM-L90 Roll Paper Consumable SpecificationsReceipt Roll Paper Specified Receipt Roll Paper Specified Original Roll Paper Print Density Adjustment Paper to Use for High Speed Requirements for Black Mark Position for Receipt Paper Black Mark Interval Requirement Die-Cut Label Roll Paper Specified Die-Cut Label Roll Paper SpecificationsDie-Cut Label Paper Specified Original Paper Consumable Specifications B-7 Requirements for Die-Cut Label Size Label Size Requirement Requirements for Transparency Rate of Die-Cut Label Paper Requirements for Black Mark Position 10Consumable Specifications Continuous Label Paper Continuous Label Roll PaperSpecified Continuous Label Roll Paper Requirements for Size of Continuous Label Paper TM-L90 with Peeler Roll Paper 14Consumable Specifications Consumable Specifications B-15 16Consumable Specifications If paper other than the specified original paper is used 18Consumable Specifications Consumable Specifications B-19 20Consumable Specifications Consumable Specifications B-21 22Consumable Specifications Consumable Specifications B-23 24Consumable Specifications Character Code Table 0 PC437 USA, Standard Europe 1 Katakana 2 PC850 Multilingual 3 PC860 Portuguese 4 PC863 Canadian-French 5 PC865 Nordic 16 WPC1252 17 PC866 Cyrillic #2 18 PC852 Latin2 19 PC858 Euro 255 Blank International Character Set Country Case Specifications Option SpecificationsElectrical Characteristics Case specifications AC Cable Selection Material Cleaning the autocutter TM-L90 only MaintenanceAdhesive adheres on cutter blade Adhesive being removed with flat-blade screwdriver Print Head Cleaning 4Maintenance Cleaning the peeler TM-L90 peeler specification only 6Maintenance Power Power LED TroubleshootingPanel LED and Error Status Power Power LED Error Error LED Error Error LEDNo Roll Paper Paper OUT LED Automatically recoverable errors Error codeAutomatically recoverable errors Recoverable errors Recoverable Errors Troubleshooting F-5 Unrecoverable errors Unrecoverable Errors Troubleshooting F-7 8Troubleshooting When a paper jam occurs TM-L90 peeler specification 10Troubleshooting Shipping Procedures 2Shipping Procedures Page Seiko Epson Corporation