Zebra Technologies GC420t manual Determining Printer Configuration, Thermal Printing

Page 42

30

Determining Printer Configuration

Determining Printer Configuration

The printer uses a ZPL printer configuration status label to report the printer’s configuration status for both EPL and ZPL operations.The ZPL style label provides a more intuitive and functionally descriptive naming conventions than the EPL style printer status label. Operational status (darkness, speed, media type, etc.), installed printer options (network, interface settings, cutter, etc.) and printer description information (serial number, model name, firmware version, etc.) are all includes on the status label. See Printing a Test (Printer Configuration) Label on page 19 to print this label. See Appendix: ZPL Configuration

on page 87 for detail on printer configuration and the ZPL commands that control the printer settings listed on the Printer Configuration Status Label.

To get an EPL style printer configuration status label, send the printer the EPL U command. See the EPL programmer’s guide for more information on the various EPL U commands and interpreting the settings displayed on these labels.

Long Term Printer In-activity or Storage

Overtime the printhead may stick to the platen (drive) roller. To prevent this, always store the printer with a piece of media (a label or paper) between the printhead and platen roller. Do not ship the printer with a roll of media installed or damage to the printer or media may result.

Thermal Printing

Caution • The printhead becomes hot while printing. To protect from damaging the printhead and risk of personal injury, avoid touching the printhead. Only use the cleaning pen to perform printhead maintenance.

Caution • The discharge of electrostatic energy that accumulates on the surface of the human body or other surfaces can damage or destroy the printhead or electronic components used in this device. You must observe static-safe procedures when working with the printhead or the electronic components under the top cover.

P1052686-001

GC420t™ User Guide

5/22/2012

Image 42

Contents Zebra GC420t P1052686-001 GC420t User Guide 22/2012 Iii FCC Compliance Statement Contents About This DocumentWho Should Use This Document How This Document Is OrganizedContacts Mail Back Technical LibraryDocument Conventions Icons UsedContents Print Operations Appendix Dimensions P1052686-001 GC420t User Guide 22/2012 Introduction GC420t Thermal Printers What’s in the Box? Unpack and Inspect the PrinterYour Printer Opening the printerPrinter Features Operator Controls Power Switch Feed Button Status LightClosing the printer Contents Getting StartedAttaching Power Loading Roll Media Preparing MediaPlacing the Roll in the Media Compartment Loading Roll Media Guides Loading Transfer Ribbon Loading Transfer Ribbon Loading Transfer Ribbon Loading Transfer Ribbon Printing a Test Printer Configuration Label Pre-install Windows Printer Drivers Universal Serial Bus USB Device Communications Serial Port and Windows operating systemsConnecting your Printer to a Computer Interface Cable RequirementsUSB Interface Requirements Serial Communications AutobaudEPL Y Command Parallel Port Testing Communications by Printing After Your Printer is ConnectedAfter Your Printer is Connected Print Operations Determining Printer Configuration Long Term Printer In-activity or StorageThermal Printing Modes of Printing Print Media TypesTypes of Media Roll and Fanfold Media Replacing Supplies Determining Thermal Media TypesAdding a New Transfer Ribbon Adjusting the Print Width Adjusting the Print QualityReplacing a Partially Used Transfer Ribbon Media Sensing When to Use Ribbon Ribbon OverviewCoated Side of Ribbon Ribbon Test with Adhesive Ribbon Scratch TestPrinting on Fan-Fold Media Printing on Fan-Fold Media Printing with Externally Mounted Roll Media Externally Mounted Roll Media ConsiderationsFonts and Your Printer Localizing the Printer with Code PagesIdentifying Fonts in Your Printer ZPL FontsStand Alone Printing Sending Files to the Printer Print Meter Printer Options Label Dispenser Option XA MMP XZLabel Dispenser Option Label Dispenser Option Zebra KDU Printer Accessory KDU Plus Printer Accessory ZBI 2.0 Zebra Basic Interpreter ZBI 2.0 Zebra Basic Interpreter Maintenance Cleaning See Cleaning the Printhead onCleaning the Printhead Media Path Considerations Sensor Cleaning Platen Cleaning and Replacement Maintenance Other Printer Maintenance Replacing the Printhead Maintenance Unplug both bundles of printhead wires from their connectors Maintenance Troubleshooting Status Light Descriptions Status Light Error Resolutions Ribbon is out Printhead is over temperatureMedia is out Printhead is openPrint Quality Problems No print on the labelPrinted image does not look right Print Quality Problems Is the printer in pause mode? If so, press the Feed button Manual Calibration Troubleshooting Tests Printing a Configuration LabelRecalibration Resetting the Factory Default Values Communications DiagnosticsCommunications Diagnostics Feed Button Modes Flash Sequence ActionPower On Modes Feed Button Modes Appendix Interface Wiring Universal Serial Bus USB Interface Parallel Interface HostConnecting the Printer to a DCE Device Serial Port InterfaceAppendix Dimensions External GC420t Printer Dimensions Optional Label Dispenser External GC420t Printer Dimensions Appendix ZPL Configuration Managing the ZPL Printer Configuration ZPL Printer Configuration FormatZPL Configuration Status to Command Cross-reference Configuration Label PrintoutDefault 65536k.......B only displays this if installed Printer Memory Management and Related Status Reports ZPL Programming for Memory Management~WC Printer Memory Management and Related Status Reports