Zebra Technologies GC420t manual Label Dispenser Option, Xa Mmp Xz

Page 58

46

Label Dispenser Option

Label Dispenser Option

The factory installed label dispenser option allows you to print a label with backing (liner/web) being removed from the label as it prints, ready for application. When printing multiple labels, removing the dispensed (peeled) label notifies the printer to print and dispense the next label.

To use dispenser-mode correctly, use your printer driver to activate the label (taken) sensor along with these typical label settings which include but are not limited to length, non- continuous (gap), and web (liner). Otherwise, you must send the ZPL or EPL programming commands to the printer.

When programming in ZPL, you can use the following command sequences shown below and refer to your ZPL Programming Guide for more information on ZPL programming.

^XA ^MMP ^XZ

^XA ^JUS ^XZ

When programming in EPL, send the Options (O) command with the ‘P’ command parameter (OP) to enable the Label Taken sensor. Other printer option parameters may also be included with the Options command string. Refer to your EPL Programmer’s Guide for more information on programming with EPL and the Options (O) command behaviors.

1.Load your labels into the printer. Close the printer and press the Feed button until a minimum of 4 inches or 100 millimeters of exposed labels exit the printer. Remove the exposed labels from the liner.

P1052686-001

GC420t™ User Guide

5/22/2012

Image 58

Contents Zebra GC420t P1052686-001 GC420t User Guide 22/2012 Iii FCC Compliance Statement Contents About This DocumentWho Should Use This Document How This Document Is OrganizedContacts Mail Back Technical LibraryDocument Conventions Icons UsedContents Print Operations Appendix Dimensions P1052686-001 GC420t User Guide 22/2012 Introduction GC420t Thermal Printers What’s in the Box? Unpack and Inspect the PrinterYour Printer Opening the printerPrinter Features Operator Controls Power Switch Feed Button Status LightClosing the printer Contents Getting StartedAttaching Power Loading Roll Media Preparing MediaPlacing the Roll in the Media Compartment Loading Roll Media Guides Loading Transfer Ribbon Loading Transfer Ribbon Loading Transfer Ribbon Loading Transfer Ribbon Printing a Test Printer Configuration Label Pre-install Windows Printer Drivers Universal Serial Bus USB Device Communications Serial Port and Windows operating systemsConnecting your Printer to a Computer Interface Cable RequirementsUSB Interface Requirements Serial Communications AutobaudEPL Y Command Parallel Port Testing Communications by Printing After Your Printer is ConnectedAfter Your Printer is Connected Print Operations Long Term Printer In-activity or Storage Determining Printer ConfigurationThermal Printing Modes of Printing Print Media TypesTypes of Media Roll and Fanfold Media Determining Thermal Media Types Replacing SuppliesAdding a New Transfer Ribbon Adjusting the Print Quality Adjusting the Print WidthReplacing a Partially Used Transfer Ribbon Media Sensing Ribbon Overview When to Use RibbonCoated Side of Ribbon Ribbon Test with Adhesive Ribbon Scratch TestPrinting on Fan-Fold Media Printing on Fan-Fold Media Printing with Externally Mounted Roll Media Externally Mounted Roll Media ConsiderationsFonts and Your Printer Localizing the Printer with Code PagesIdentifying Fonts in Your Printer ZPL Fonts Stand Alone Printing Sending Files to the Printer Print Meter Printer Options Label Dispenser Option XA MMP XZLabel Dispenser Option Label Dispenser Option Zebra KDU Printer Accessory KDU Plus Printer Accessory ZBI 2.0 Zebra Basic Interpreter ZBI 2.0 Zebra Basic Interpreter Maintenance Cleaning See Cleaning the Printhead onCleaning the Printhead Media Path Considerations Sensor Cleaning Platen Cleaning and Replacement Maintenance Other Printer Maintenance Replacing the Printhead Maintenance Unplug both bundles of printhead wires from their connectors Maintenance Troubleshooting Status Light Descriptions Status Light Error Resolutions Ribbon is out Printhead is over temperatureMedia is out Printhead is openNo print on the label Print Quality ProblemsPrinted image does not look right Print Quality Problems Is the printer in pause mode? If so, press the Feed button Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Resetting the Factory Default Values Communications DiagnosticsCommunications Diagnostics Feed Button Modes Flash Sequence ActionPower On Modes Feed Button Modes Appendix Interface Wiring Universal Serial Bus USB Interface Parallel Interface HostConnecting the Printer to a DCE Device Serial Port InterfaceAppendix Dimensions External GC420t Printer Dimensions Optional Label Dispenser External GC420t Printer Dimensions Appendix ZPL Configuration Managing the ZPL Printer Configuration ZPL Printer Configuration FormatZPL Configuration Status to Command Cross-reference Configuration Label PrintoutDefault 65536k.......B only displays this if installed Printer Memory Management and Related Status Reports ZPL Programming for Memory Management~WC Printer Memory Management and Related Status Reports