Zebra Technologies GC420t manual Platen Cleaning and Replacement

Page 70

58

Maintenance

Cleaning

Platen Cleaning and Replacement

The standard platen (drive roller) normally does not require cleaning. Paper and liner dust can accumulate without effecting print operations. Contaminates on the platen roller can damage the printhead or cause the media to slip or stick when printing. Adhesive, dirt, general dust, oils and other contaminates should be cleaned immediately off the platen.

Clean the platen (and media path) whenever the printer has significantly poorer performance, print quality or media handling. The platen is the print surface and drive roller for your media. If sticking or jamming continues even after cleaning, you must replace the platen.

The platen can be cleaned with a fiber-free swab (such as a Texpad swab) or a lint free, clean, damp cloth very lightly moistened with medical grade alcohol (90% pure or better).

1.Open the cover (and dispenser door). Remove media from platen area.

2.Pull the platen bearing latch release tabs on the right and left sides towards the front of the printer and rotate them up.

Platen Bearings

P1052686-001

GC420t™ User Guide

5/22/2012

Image 70

Contents Zebra GC420t P1052686-001 GC420t User Guide 22/2012 Iii FCC Compliance Statement Contents About This DocumentWho Should Use This Document How This Document Is OrganizedContacts Mail Back Technical LibraryDocument Conventions Icons UsedContents Print Operations Appendix Dimensions P1052686-001 GC420t User Guide 22/2012 Introduction GC420t Thermal Printers What’s in the Box? Unpack and Inspect the PrinterYour Printer Opening the printerPrinter Features Operator Controls Power Switch Feed Button Status LightClosing the printer Contents Getting StartedAttaching Power Loading Roll Media Preparing MediaPlacing the Roll in the Media Compartment Loading Roll Media Guides Loading Transfer Ribbon Loading Transfer Ribbon Loading Transfer Ribbon Loading Transfer Ribbon Printing a Test Printer Configuration Label Pre-install Windows Printer Drivers Universal Serial Bus USB Device Communications Serial Port and Windows operating systemsConnecting your Printer to a Computer Interface Cable RequirementsUSB Interface Requirements Serial Communications AutobaudEPL Y Command Parallel Port Testing Communications by Printing After Your Printer is ConnectedAfter Your Printer is Connected Print Operations Long Term Printer In-activity or Storage Determining Printer ConfigurationThermal Printing Modes of Printing Print Media TypesTypes of Media Roll and Fanfold Media Determining Thermal Media Types Replacing SuppliesAdding a New Transfer Ribbon Adjusting the Print Quality Adjusting the Print WidthReplacing a Partially Used Transfer Ribbon Media Sensing Ribbon Overview When to Use RibbonCoated Side of Ribbon Ribbon Test with Adhesive Ribbon Scratch TestPrinting on Fan-Fold Media Printing on Fan-Fold Media Printing with Externally Mounted Roll Media Externally Mounted Roll Media ConsiderationsFonts and Your Printer Localizing the Printer with Code PagesIdentifying Fonts in Your Printer ZPL FontsStand Alone Printing Sending Files to the Printer Print Meter Printer Options Label Dispenser Option XA MMP XZLabel Dispenser Option Label Dispenser Option Zebra KDU Printer Accessory KDU Plus Printer Accessory ZBI 2.0 Zebra Basic Interpreter ZBI 2.0 Zebra Basic Interpreter Maintenance Cleaning See Cleaning the Printhead on Cleaning the Printhead Media Path Considerations Sensor Cleaning Platen Cleaning and Replacement Maintenance Other Printer Maintenance Replacing the Printhead Maintenance Unplug both bundles of printhead wires from their connectors Maintenance Troubleshooting Status Light Descriptions Status Light Error Resolutions Ribbon is out Printhead is over temperatureMedia is out Printhead is openNo print on the label Print Quality ProblemsPrinted image does not look right Print Quality Problems Is the printer in pause mode? If so, press the Feed button Manual Calibration Printing a Configuration Label Troubleshooting TestsRecalibration Resetting the Factory Default Values Communications DiagnosticsCommunications Diagnostics Feed Button Modes Flash Sequence ActionPower On Modes Feed Button Modes Appendix Interface Wiring Universal Serial Bus USB Interface Parallel Interface HostConnecting the Printer to a DCE Device Serial Port InterfaceAppendix Dimensions External GC420t Printer Dimensions Optional Label Dispenser External GC420t Printer Dimensions Appendix ZPL Configuration Managing the ZPL Printer Configuration ZPL Printer Configuration FormatZPL Configuration Status to Command Cross-reference Configuration Label PrintoutDefault 65536k.......B only displays this if installed Printer Memory Management and Related Status Reports ZPL Programming for Memory Management~WC Printer Memory Management and Related Status Reports