Nortel Networks Instant Internet 400 Unit manual Mounting your Instant Internet unit in a rack

Page 37

Chapter 3 Instant Internet 400 hardware installation 37

2Attach one end of the communications cable (modem, ISDN, T1, DDS, Ethernet, token ring) to the appropriate connector on the Instant Internet unit.

3Attach the other end of the communications cable to the appropriate source (phone jack, ISDN jack, T1 jack, DDS jack, cable modem, or external router).

4Attach the Instant Internet unit to a hub on your LAN using an Ethernet cable (attach to Eth1) or a token ring cable (attach to Tok1).

Note: A token ring cable is not included with your Instant Internet package.

5Plug the power cord into the rear panel of the Instant Internet unit.

6Plug the power cord into an AC wall outlet.

7Turn on the Instant Internet unit.

When you turn on your Instant Internet 400 unit, the LEDs on the front panel illuminate. LED #2 glows amber when the unit is ready for setup. For information about setting up your unit, see Installing the BayStack Instant Internet Management Software Version 7.11

Mounting your Instant Internet unit in a rack

To install your Instant Internet in an equipment rack, you will need a Phillips screwdriver (not included) and the brackets, screws, and washers provided in the rack mounting kit.

To mount your Instant Internet 400 in a rack:

1Remove the three screws from the cover on each side of your Instant Internet unit as shown in Figure 3.

Setting Up the BayStack Instant Internet 400 Unit

Image 37

Contents Setting Up the BayStack Instant Internet 400 Unit Trademarks Copyright 2000 Nortel NetworksStatement of conditions USA requirements onlyJapan/Nippon requirements only Setting Up the BayStack Instant Internet 400 UnitTaiwan requirements Canada requirements onlyCanada CS-03 -- Règles et règlements Nortel Networks NA Inc. software license agreementSetting Up the BayStack Instant Internet 400 Unit Modular components used in this assembly FCC Part 68 compliance statement UL listing/C-UL listing Connecting an Instant Internet unit to the networkNT1 Instant Internet Isdn Device 300867-G Contents Contents Chapter DIP switch settingsFigures Figures 300867-G Tables Tables 300867-G Before you begin PrefacePreface AcronymsRelated publications How to get help Instant Internet package Chapter IntroductionIntroduction Available optionsRequirements and compatibility Introduction 300867-G Preparing for Internet access Chapter Installation preparationInstallation preparation Selecting an Internet service providerMaking decisions Installation checklist Installation checklistInstallation preparation Installation checklist ISP Connection Alternate Phone Number Installation worksheetT1 Connection Information Getting to know your Instant Internet 400 unit Chapter Instant Internet 400 hardware installationRear panel of the Instant Internet 400 unit Instant Internet 400 hardware installationInterface name Interface card Type LAN interfacesCommunication interfaces DDS Instant Internet quick installationInstant Internet 400 hardware installation Mounting your Instant Internet unit in a rack Removing screws from cover of Instant Internet 400 unit 10046FA Instant Internet 400 hardware installation 300867-G DIP switches Chapter DIP switch settingsSwitch settings for token ring speed Switch settings for normal operationSingle token ring switch settings Dual token ring 16 Mb/s Tok1 / 16 Mb/s Tok2 Dual token ring switch settingsDual token ring 16 Mb/s Tok1 / 4 Mb/s Tok2 Dual token ring 4 Mb/s Tok1 / 16 Mb/s Tok2Switch settings for resetting the password Switch settings for special configurationsSwitch settings for restoring factory default conditions Refer to Switch settings for special configurations on Resetting your Instant Internet unitLEDs at power-up sequence Chapter LEDs support and diagnostic functionsInterpreting LEDs Recognizing dual token ring speed Recognizing single token ring speedLED status and appearance during operation LEDs during operationLEDs support and diagnostic functions 300867-G Physical specifications Appendix a Technical specificationsEnvironmental specifications Appendix a Technical specifications 300867-G Adapter cable part numbers Appendix B Adapter cable pinout diagramsAdapter cable Appendix B Adapter cable pinout diagramsDCE adapter cable 21 DCE adapter cable diagramAppendix B Adapter cable pinout diagrams 300867-G Index SymbolsNumbers Index Index Index