Speaker Interface

get fixed. We go to a lot of trouble to make products reliable, and the failure rate of our amplifiers is very low. This is small comfort to the few, but take it easy and give us a call if you have problems.

People are interested in how long it takes for these amplifiers to break in. It takes about an hour for them to warm up, and this is where we adjust them first. Then we adjust them again and again over a couple of days, keeping the bias and offset in the sweet spot. Our environment is about 23 degrees Centigrade, room temperature, and the heat sinks will rise to about 25 degrees C. above that, for a heat sink temperature of 48 degrees C.

In your setup the temperature may vary a bit due to line voltage and ventilation, but it is not a big deal. You should be able to put your hands on the heat sinks without discomfort for 10 seconds or so.

The amplifier has a thermal cutout that will disconnect AC power if the temperature exceeds 75 degrees Centigrade. This should never occur in real life.

More things to know: You can remotely operate the stand-by mode by applying 12 volts DC to the single pair of 5 way connectors on the rear of the amplifier. The positive of the 12 volts DC goes to the red connector. This connection has an actual operating range of about 9 volts to 15 volts. This switching will override the front panel button, so if you want the button to operate, leave the rear connection open.

So much for the most essential information.

The X250 is optimized for loads nominally rated at 4 ohms and above. You can run the amplifiers into a lower nominal impedance without difficulty, and we are not aware of a speaker on the market that presents unusual difficulty with these amplifiers.

The X amplifiers do not care particularly about the reactivity of the load. Reactive loads typically will have slightly less distortion at a given voltage/current level than resistive loads, but will make the amplifier run a little hotter. The X circuit was designed to be quite happy driving electrostatic and other speakers.

When driving transformer-coupled loads directly, as in some electrostatic and ribbon designs, some attention must be paid to the DC character of the situation. If the transformer primary is being driven raw with no protection from DC and your source has DC voltage, or in cases where the small offset of the power amplifier is still too much, you may create distortion in the transformer and get less than optimal performance from it. Generally this is not the case with transformer coupled loudspeakers, but it does occasionally surface. In these cases, take special care that the source does not contain a differential DC component, and confirm the differential DC offset of the amplifier is sufficiently low. This is easily adjusted by a qualified technician armed with the service manual. Again, consult your dealer or call us.

Page 4

X250 specifications

The Pass Labs X250 is a distinguished power amplifier that showcases the brand's commitment to delivering high-quality audio performance, blending robust engineering with innovative technology. Known for its exceptional build quality and sonic capabilities, the X250 is designed for audiophiles and music enthusiasts who demand the best from their audio equipment.

At its core, the X250 is a Class A/B amplifier, which means it combines the efficiency of Class B with the superior sound quality of Class A. This hybrid design allows the amplifier to deliver high power output while maintaining low distortion levels, resulting in a clean, dynamic sound that captures the essence of the original recording. The amplifier delivers 250 watts into 8 ohms and 500 watts into 4 ohms, making it suitable for driving a wide range of loudspeakers with ease.

One of the standout features of the X250 is its use of Pass Labs' proprietary “Bias Current” technology. This innovative system optimizes performance by ensuring that the output devices operate in their most linear region, reducing crossover distortion and enhancing the amplifier's overall sound quality. This results in a more accurate and natural reproduction of audio, appealing to listeners who seek fidelity above all else.

Another notable characteristic of the X250 is its impressive dynamic range. The amplifier is designed to handle transient peaks with confidence, preserving the impact and nuance of musical passages, whether it's the delicate pluck of a guitar string or the thunderous notes of a full orchestra. The low noise floor further enhances the listening experience, allowing even the quietest details to be heard clearly.

The build quality of the X250 is equally impressive, featuring a rugged chassis and high-grade components that ensure durability and reliability. With its elegant appearance, the amplifier is not only a functional piece of equipment but also an attractive addition to any audio setup. The attention to detail in the design is evident, with a focus on minimizing vibrational interference and maintaining signal integrity.

In conclusion, the Pass Labs X250 is a remarkable power amplifier that combines advanced technology with exceptional sound quality. Its Class A/B design, Bias Current technology, and high power output make it a versatile choice for a wide range of audio applications. For those who value both performance and aesthetics, the Pass Labs X250 stands out as a superb option in the realm of high-fidelity audio amplification.