AMX Installing the PC Presenter for AXlink Operation, Using AXlink for data and power

Page 20

Installing the PC Presenter

GN

ExternalIRSenso IRI

OutputonAXR-MS AU

PW

FIG. 17 IRX-SM+ or IRX-DM+ external IR sensor wiring diagram

GND

OUT IRX-SM+or

AUXOT IRX-DM+

+12V

Installing the PC Presenter for AXlink Operation

To use the PC Presenter as an integrated AXlink device, connect the AXR-MSE to the PC keyboard/mouse and a Central Controller. As an AXlink device, the PC Presenter controls PC keyboard/mouse functions as well as the devices on the AXlink bus.

To connect the PC Presenter for AXlink operation, follow the instructions listed under Step 1, Step 2 and Step 3 starting on page 15 to connect the PC keyboard, mouse and optional external IR receiver. The following sections describe connecting AXlink for power and data, and connecting an optional external 12VDC power supply.

Using AXlink for data and power

Connect the Central Controller's AXlink connector (male) on the rear panel of the AXR-MSE for data and 12 VDC power, as shown in FIG. 18.

PWR(+)

PWR

AXR-MSE

AXP

AXP

CentralController

AXM

GND

FIG. 18 IAXlink data and power wiring diagram

AXM GND

AXlinkconector

AXlink data and 12 VDC power supply connections

Connect the Central Controller's AXlink connector to the AXlink connector (male) on the rear panel of the AXR-MSE, and the optional 12 VDC power supply as shown in FIG. 19.

PWR (+) GND (-)

PWR(+)

AXP/TX

AXM/RX GND (-)

AXB-IRS4, 12 VDC PWR connector

12 VDC power supply

PWR

AXP

Control system

AXM

GND

AXB-IRS4, AXlink/RS232 connector

FIG. 19 IAXlink and optional 12 VDC power supply wiring diagram

	16	PC Presenter

Image 20

Contents PC Presenter AMX Limited Warranty and Disclaimer Table of Contents Programming Transmitter Pushbuttons Introduction PC Presenter transmitter and receiver unitsTXC-MSL Specifications TXC-MSL TransmitterTXC-MSL mouse controls Trigger switchTXC-MSL controls Front Panel AXR-MSE Wireless Mouse and Keyboard ControllerAXR-MSE Specifications Rear Panel Keyboard IN/OUTIntroduction IR and RF Settings Pre-InstallationSetting the TXC-MSL transmitter DIP switch Radio codes DIP switch positions Channel code ranges From Radio Code SettingsSetting radio codes Setting the Device DIP switch TXC-MSL pushbutton configurationPosition Using the PC Presenter Without a PC ComputerDevice DIP switch positions and values SW3 SW2 Setting Mouse Mode Wiring RequirementsWiring guidelines Wiring GuidelinesPreparing captive wires Wire sizePre-Installation Installing the PC Presenter Installing the PC Presenter for Stand Alone OperationConnecting the AXR-MSE to the PC keyboard and PC Connecting the AXR-MSE to the PC mouse and PCAXlink data and 12 VDC power supply connections Installing the PC Presenter for AXlink OperationUsing AXlink for data and power LED indicators Installing the PC Presenter Programming the PC Presenter Programming the PC Presenter in Stand Alone ModeUsing PC Presenter Commands Short form listing of keycodes List commands HelpClear memory Programming Transmitter Pushbuttons Display available memoryLong form list of stored keycodes Display version and copyright infoExiting program mode Creating a buffer for keyboard input SendCommandsSendCommands SendStrings SendStringsRMACROn-s TXIDnChannel Direction Speed Mouse Control ChannelsMouse Control Channels Using Levels Using the OLDesign Engraving Program OLDesign main window with example TXC-MS overlayUsing the OLDesign Engraving Program TXC-MSL Battery Replacement Replacing the batteriesAMX reserves