American Power Conversion Master Switch manual Operating MasterSwitch VM

Page 9

Introduction

Operating MasterSwitch VM

Initial setup

You must configure the network settings of MasterSwitch VM before it

 

can operate on a network. The required settings are:

 

• IP address of MasterSwitch VM

 

• Subnet Mask

 

• IP address of the default gateway

 

Note: If a default gateway is not present, enter an IP address

 

of a computer on the same subnet that is always active.

 

For instructions on configuring the MasterSwitch VM network settings,

 

see the installation manual included with the unit and on the CD. After

 

you have configured MasterSwitch VM, no further configuration is

 

required. The remaining MasterSwitch VM properties are pre-configured

 

at the factory. However, you may want to customize these properties for

 

your application. See Menu Items on page 14 for more details on

 

changing MasterSwitch VM properties.

Configuring

MasterSwitch VM allows you to configure an outlet for on-demand

outlets for

operation. On-demand operation consists of On, Off, and Reboot Outlet

operation

Control Actions. The sections that follow describe each operation that

 

you can configure for your MasterSwitch VM unit.

 

Immediate On. This action immediately turns an outlet on.

 

Immediate Off. This action immediately turns an outlet off.

 

Immediate Reboot. This action immediately turns an outlet off, and

 

then turns it back on after the outlet’s Reboot Duration expires.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outlet is on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Immediate Reboot

 

 

 

 

 

 

command is issued

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outlet is turned off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cancel command

is issued

Outlet remains

off

Reboot Duration

expires

Outlet is turned on

MasterSwitch VM User’s Guide

4

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MasterSwitch VM Thank You Contents MasterSwitch VMContents Troubleshooting Warranty InformationSpecifications Life-Support PolicyFeature Description IntroductionProduct Description Introduction MasterSwitch VM ControllerStatus Description LEDsOperating MasterSwitch VM Configuring outlets for operation Is turned on When these two delays expire, the outlet will be turned on Outlet will be turned on Outlets always turn on Outlets do not turn on when the Overload WarningThreshold has been exceeded Overload Warning and the load exceeds the Overload WarningManagement Interfaces Managing MasterSwitch VMControl Console Managing MasterSwitch VMInterface Telnet, for remote managementManaging MasterSwitch VM Account access to Password-Protected AccountsAccount, and up to 16 Outlet User accounts Outlets and menuOutlets Menu ItemsOutlets Menu ItemsUnit Configuration MasterSwitch VMOutlet Configuration Links Event Log Interface or by pressing C TRL + L in the Control ConsoleDir. You will see a listing similar to the following ftpdir Representation when logging and displaying event data MasterSwitch VM unit always uses four-digit yearSimilar to the following However, you may need to select a four-digit date formatTCP/IP NetworkSnmp Access Control Telnet/WebDefinition Trap Receiver IP to Snmp Trap ReceiverSystem User ManagerItems Outlet User ManagerFor Outlet User Manager Identification Date/TimeFile Transfer Tools Enable BootpHelp Security Security FeaturesSecurity AuthenticationMethods Interface Security AccessProduct Information Warranty InformationProduct Information TroubleshootingLife-Support Policy Following table shows the product specifications for SpecificationsMasterSwitch VM power distribution unit AP9221X166 ProductAP9221NX166 MasterSwitch VM Controller AP9221NX166Index Help FeaturesIndex Outlet Access Outlet operationsRegional centers APC Worldwide Customer Support
Top Page Image Contents