AMX NXA-UPS1500 manual EPM Specifications, Important Notice

Page 30

NXA-UPS1500 EPM Installation

IMPORTANT NOTICE

The EPM which is supplied with a factory input plug can be safely connected to the wall receptacle.

This EPM is connected to an UPS. There will be voltage at the output terminals if the UPS is turned on even if the input AC Mains is not available.

Make sure that the AC Utility outlet is correctly grounded.

Use a certified input power cable with the correct plugs and sockets for the appropriate voltage system.

To eliminate any overheating of the EPM, keep all ventilation openings free from obstruction and do not place any foreign objects on top of the EPM.

Keep the EPM 20 cm away from the wall.

Make sure the EPM is installed within the proper environment as specified. (0-40°C and 30-90% non-condensing humidity)

This EPM is designed for indoor use only.

This EPM is not designed for use in dusty, corrosive and salty environment.

The battery will discharge naturally if the system is unused for a period of time.

It should be recharged every 2-3 months if unused. During normal operation, the batteries will automatically remain in charged condition.

When replacing batteries, replace with the same quantity, type & capacity.

CAUTION - Do not dispose of battery or batteries in an open fire. The battery may explode.

CAUTION - Do not open or mutilate the batteries. The electrolyte from the batteries is toxic and harmful to the skin and eyes.

CAUTION - Risk of Electric Shock - Battery circuit is not isolated from AC, hazardous voltage may exist between battery terminals and ground. Test before touching with bare hands.

CAUTION - A Battery can present a risk of electrical shock and high short circuit current.

The following precautions should be observed when working on batteries:

a.Remove watches, rings, or other metal objects.

b.Use tools with insulated handles.

c.Wear rubber gloves and boots.

d.Do not lay tools or metal parts on top of batteries.

e.Disconnect charging source prior to connecting or disconnecting battery terminals.

EPM Specifications

EPM connectors are color coded as shown below. Do not try to install the EPM with connectors that are a different color from the EPM connector in the UPS.

Nominal System Voltage: 24V

Connector color: Red(+), Black (-)

26

NXA-UPS1500 Uninterruptible Power Supply

Image 30
Contents NXA-UPS1500 AMX Limited Warranty and Disclaimer Table of Contents Battery Replacement NXA-UPS1500 Uninterruptible Power Supply FeaturesOverview Product Specifications NXA-UPS1500 Product SpecificationsFront Panel LCD Other AMX EquipmentNXA-UPS1500 Uninterruptible Power Supply Important Notice Storage InstructionsImportant Safety Instructions Assembling the Battery Pack Accessing the Battery Compartment Step One Accessing the Battery Compartment Step TwoAccessing the Battery Compartment Step Three Page Place the UPS Properly Accessories for Tower and Rack MountMounting the NXA-UPS1500 UnpackingSelecting Installation Position UPS SetupTower Setup Tower Setup Step OneTower Setup Step Two Rack-Mount Setup Rack-Mount Setup Step OneRack-Mount Setup Step Two Rack-Mount Setup Step Three Rack-Mount Setup Step FourRack-Mount Setup Step Five Connecting the UPS Connect Utility and LoadConnect Network Surge Protection Connect the RS-232 Communication PortRS-232 Communication Port Pin Assignment NetLinxUPSConnecting the UPS NXA-UPS1500 Uninterruptible Power Supply Operation Operation Battery Replacement Assembling the Battery PackReplacing the UPS Battery Step One Replacing the UPS Battery Step Two Replacing the UPS Battery Step ThreeRecycling the Used Battery NXA-UPS1500 EPM Installation Important Safety InstructionsEPM Specifications Important NoticeEPM Installation and Operation Selecting Installation PositionUnpacking EPM Installation Instructions Tower Installation Step OneTower Installation Step Two Using the EPM With The UPS Use With UPS Step OneUse With UPS Step Two EPM Rack Mount Installation Rack Mount Installation Step OneRack Mount Installation Step Two Rack Mount Installation Step Three Rack Mount Installation Step FourConnecting the EPM To the UPS EPM Storage InstructionsReplacing the Battery In the EPM Replacing the Battery in the EPM Step OneReplacing the Battery in the EPM Step Two Replacing the Battery in the EPM Step Three Replacing the Battery in the EPM Step FourUPS Maintenance NXA-UPS1500 Uninterruptible Power Supply It’s Your World Take Control