GBC 1264WF, 1244WF operation manual Method for Tacking New Film to Existing Film

Page 30

GBC 1264WF/1244WF

Operation Manual

 

 

(1)

(2)

(2)

.......a PSA film or mount adhesive

Fig. 11

.......a PSA film or mount adhesive

Fig.12

Method for Tacking New Film to Existing Film

The following describes a method for loading film whereby the existing film present on the heat rollers may be used in place of the threading card to draw the new film through the laminator. The adhesive of the existing film must be tacky or liquefied. Leading edges of the new film will be overlapped onto the tacky adhesive of the old film. The existing film and the new film will be pulled through the laminator together.

CAUTION: Do not cut yourself

CAUTION: Be careful not to cut any of the rollers!

1.Cut (1) remaining top film web between the idler bar and heat roller. Cut (2) the film web between the lower film supply and the idler bar (Figure 11).

CAUTION: Be careful not to cut any of the rollers!

2.Remove the feed table down.

3.Do not allow the adhesive side of the film to contact the heat or pull rollers. Liquefied or tacky adhesive deposited on heat rollers will require the rollers to be cleaned per the section tilted.

4.Replace both the top and bottom rolls of film with new rolls. Ensure the adhesive side is facing out.

5.Pull the film around the idler bars, with the exception of PSA mounting adhesives without a release liner.

6.Tack the new film to the existing film on the heat rollers. For PSA film, attach the release liner to the rewind tube

7.Use the footswitch to advance the film into the heat roller nip.

8.Observe the film being pulled through the laminator to assure that the remaining existing film and the new films are advancing concurrently. Any separation between the films will require stopping the motor immediately and the situation corrected.

9.Press STOP once the newly threaded film has completely exited the pull rollers.

© 200 6 General Binding Corporation

Page 30

Image 30
Contents GBC Titan 1264WF/1244WF GBC 1264WF/1244WFGBC 1264WF/1244WF Table of Contents Service Important Safety InstructionsImportant Safeguards GeneralWarranty SpecificationsPRE-INSTALLATION InstallationGBC 1264 WF/1244 WF Requires Detailed Specifications Description Features ApplicationsConsumables Function ElectricalSpeed Motor Heating Capabilities Controls Roll Design GBC 1264WF/1244WF Connectors for 1264 WF Connectors for 1244 WF1244 WF 1244WF CE ∙ Crated 57 in.H x 68 in. W x 38 in. D Dimensions∙ Uncrated 49inH x 77.25 in.W x 25.5 in. D Nip Height 35.63 in 91cmKnow your Laminator GBC 1264WF/1244WF GBC 1264WF/1244WF Unwind Brake Display Control Panel Top and Bottom Temperature StopReverse Auto-Off ReadySafety Safety ShieldGBC 1264WF/1244WF Safety Shield How to Guide Loading FilmGBC 1264WF/1244WF Loading Film GBC 1264WF/1244WF Select and Change the Nip GBC 1264WF/1244WF In-Line Slitters Rear Cut-Off BladeApplications Film Loading & ThreadingTo load a roll of film Webbing Thermal Film Using Threading Card Webbing Using Film Threading Card for PSA FilmWebbing PSA Film/Mount Adhesive Using Threading Card Start Laminating Method for Tacking New Film to Existing Film To Unweb the laminator Clearing a Film Jam Wrap-upTo clear a jam Tips for Pre Coating Boards Tips for Mounting Pre Coated BoardsTips for Single Sided lamination Tips for Creating a Decal Tips for mounting a DecalTips for Thermal Encapsulation Tips for Accushield Speed / Temperature Control ART of LaminationHeat OutputMaintenance Caring For the GBC 2064WF LaminatorService Agreement TensionGBC 1264WF/1244WF