Epson 410 manual ABxxxxxxxx

Page 45

Chapter 5

Printer Commands

))))))))))))))))))))))))))))))))))))))))))))

^A ^D COMMAND

22Change SW2: Software dip switch #2. Below is the ^AB sequence:

12345678

^ABxxxxxxxx

*******.)))),

******.)))),*

*****.)))),**

*****RRR Power-up Label Format

*****000=ALWAYS EPROM Format 1

*****001=ROM or Saved Format File 1

*****010=ROM or Saved Format File 2

*****011=ROM or Saved Format File 3

*****100=ROM or Saved Format File 4

*****101=ROM or Saved Format File 5

*****110=ROM or Saved Format File 6

*****111=ROM or Saved Format File 7

****.))))Q 1=Use Saved Format File, 0=Rom Format

***.)))))Q 1=Print Button Enable, 0=Disable **.))))))Q 1=Disable Button Use, 0=Enable *.)))))))Q 1=>RESTARTED< Response Enable,

0=Disable

.))))))))Q 1=Clear Text Enable, 0=Disable

Position:

1Clear Text Function: If enabled, all variable text strings will be erased when a ^D2<CR> is processed.

2>RESTARTED< Response: If the printer has been reset and this switch has been enabled, the printer will respond with to the first poll by sending the >RESTARTED< message. If additional enquiries are made the printer will respond normally. The >RESTARTED< message is only sent once after reset.

3Button Use: Set to 1, the printer will not allow button use, even for paper feed.

4Print Button: If this is 0, the button can be used for paper feed, but cannot be used to initiate label printing.

5Power-up Format Type: Defines the power-up label format. This parameter

determines whether to use a saved format file for the power-up label, or a ROM format (defined by positions 6, 7, and 8). The saved format file must be battery backed to use the saved format file feature. See Appendix C for configuration instructions and section 5.3.7 for saved format file information. Please consult your service organization if changes or additions to the fixed ROM formats are required.

6,7,8 Power-up Label Format: These switches decide which format to use at power- up.

))))))))))))))))))))))))))))))))))))))))))))

410 Operators Manual

39

Image 45
Contents Microcom Corporation Operators Manual Table of Contents Table of Contents Table of Contents List of Tables Introduction Operators Manual Features and Specifications BAR Codes RAM PhysicalPrinter Variations Front View Operators Manual Batch Mode Normal ModeStatus Label Mode Basic OperationSerial Parameters 9600-N-8-1 PAPER-OUT ModeStatus Light Light Mode Meaning ColorNormal and TAG/TEAR Modes Loading PaperClearing Label Misfeeds Diaphragm Removal PEEL-AND-DISPENSE ModeCleaning Instructions Cable Pinout CommunicationsPrinter Cables PC Connection Serial Designing Labels Using LDSCcopy Filename COM1 PC Connection ParallelCcopy Filename LPT1 Easycr Learning LDSMicrocom Makes Itcr HellocrDesigning Labels Using LDS Chapter Label Header LSX Label Size X Direction HFM Number of Fields in LayoutLSY Label Size Y Direction WEB WEB SizeLCB Label Control Byte DPS MM/SEC Inches PER Second MinuteAGD Number of Steps to Activate GAP Detector 615,153,,20,30,,70,4CR Sample Session with a Label HeaderTSN Text String Number Label FieldsXB X Beginning Coordinate YB Y Beginning CoordinateTCI Text Conversion Identifier CC Character CountCGN Character Generator Number CGNOCR-A UPC/EAN Left Justified Right JustifiedCentered Above BaselineCMY Character Multiplier Y Direction CMX Character Multiplier X DirectionTSP Text Starting Position CLX Character Cell Length X DirectionCLY Character Cell Length Y Direction 100, 40, 4, 1,4CR Sample Session with a Label FieldSpecial Printer Control Codes Printer CommandsPrinter Enquiries Sending D Printer Commands Command Software DIP Switches and Eeprom CommandsPosition ABxxxxxxxxABxxxxxxxx Position Always ABxxxxxxxx Printing Commands CommandClear commands LSY AUTO-SIZING and Valid GAP CommandsGAP AGDCommand Auto-Size Label D30 CR Hhmmss CR DD/MN/YR/W CR REAL-TIME Clock= SUN = MONEuropean Date Formatcr US Date FormatcrClock Optioncr Disable increment and decrement Serial Number CommandsSingle Serial Number Status D85Command Load label control byte LCB a specifies the number Label Header CommandsSaving Format Files Commands Send Saved Format File to Serial Port a selects which oneUsage File #1 ESCFile #2 File #3 Label Presence Sensor Control Command Command Clears command Text Strings CommandsShip Fromcr Miscellaneous Printer Commands Enable 450 Emulation Disable AllEnable 1 Enable 460 EmulationRequired for the Logo Option LogosProcedure for Using the PCX2410 Software Chapter Printer Commands Opening Parameters Format of Logo FilesChapter Printer Commands Designing with BAR Codes Rotationscr DegreescrHuman Readables Chapter Printer Commands UPC-A HR W/CHKSUMCR UPC-A HR W/O Chksumcr 01234567890CR Making Lines Thick LinesHalf Lines Reverse Video LOT NumbercrQtycr Label Support Rack CLOCK/BATTERY Backed RAM SocketLarge Paper Roll Supply Holder PCX2410 SoftwareCleaning KIT Wysiwyg Software PackagesParallel Conversion Boards Limited Warranty Appendix a Warranty and Repair ProceduresReturn Material Authorization RMA Procedure Appendix B Cleaning KIT & Accessories Battery Backed RAM with REAL-TIME Clock Appendix C Configuration GuideAddition Format Area Graphic ImagesAppendix D Installing the Label Support Rack Appendix E More Label Samples Default POWER-UP LabelFonts UPC-A HR W/CHKSUMCR UPC-A HR W/O Chksumcr 01234567890CR Multipliercr XY Multipliercr 1XYCR 2XYCR 4XYCR 8XYCR D3CR Linescr Offset of 100CR D3CR Offset of 0CR D3CRD57CR 620,441,,10,25,,,352CR 100,100,13,1,13CR D56CR D2CR Aiag Label Wheelcr Aacr Appendix F Sample Basic Program Disk Label MakerPrint Print Print Close System Appendix G Quick Reference Command Summary Not Used Column Epson emulation 2 inch Printer StatisticsPage Auto-Size Label Section Emulation Control Text Mode Control SectionClears Commands 86, 88 Peel-and-Dispense Mode Section Advance when idleTurn off peel-and-dispense mode Turn on peel-and dispense modeIndex Chapter Printer Commands Printer Commands Chapter Operators Manual