Brady BBP81 manual Setting Alerts, BradyConnect Alerts

Page 66

66

BradyConnect WebView

Alert Setup

Setting Alerts

Your 10/100 Internal Print Server allows you to configure your printer to send unsolicited Alerts.

Table 9 shows the conditions that can trigger alerts.

		Table 9 • Alerts

Alert Type	Error Condition

BradyConnect Alerts	•	Media out
	•	Ribbon out
	• Printhead over-temp warning
	• Printhead under-temp warning
	•	Head open
	• Power supply over-temp
	• Ribbon warning (in direct-thermal mode)
	•	Rewind full
	•	Cut error
	•	Printer paused
	•	PQ job completed
	•	Label taken
	•	Head element out
	•	Power on

This section has step-by-step instructions for setting up an alert using BradyConnect.

Important • If you do not have a BradyConnect-enabled printer, these steps will not work.

Y885775

BradyConnect 10/100 Internal Print Server User Guide

07/18/2008

Image 66

Contents Page Page Contents Print Protocols Frequently Asked Questions Glossary Index This page intentionally left blank Contents About This DocumentWho Should Use This Document How This Document Is OrganizedCorporate Headquarters Technical ServiceContacts Other WebsitesDocument Conventions ZtoolsAbout This Document Related Documents Introduction Overview ComponentsBrowser Support RequirementsFirmware ProtocolsCompatibility Technical Specifications for the 10/100 Internal PS Introduction 10/100 Internal Print Server 10/100 Internal PS Features Status and ConfigurationUser ID admin Password To access the print server settings, complete these steps Printer HomePrint Server Settings Print Server Configuration TCP/IP Configuration Menu OptionsTCP/IP Logical Printing Ports Smtp Email Alert Configuration System SnmpWeb Admin POP3 Email PrintingConfiguration Sheet Print Server StatusTo view the port status, complete this step Port StatusReset To reset the 10/100 Internal PS, complete these stepsRestore Make the selections you want, and click Submit Changes10/100 Internal Print Server Getting Started Before You Begin Network Configuration Label for BBP81 4/BBP81 Getting Started View the Method to Obtain an IP Address Print a Network Configuration LabelReset the Wired or Wireless Network View the Print Engine’s IP AddressDefaulting the 10/100 Internal PS Defaulting the 10/100 PS on the BBP81 4 and BBP81 6 PrintersRestore to Factory Defaults WebViewWith Dynamic Host Configuration Protocol Dhcp Assigning an IP AddressWithout Dhcp A Non-Windows Environment Assigning an IP address from the printer LCDAssigning an IP Address via a Telnet Session To use this method, complete these stepsGleaning Getting Started BradyConnect WebView WebView HomeView Printer Configuration To open WebView for your printer, complete these stepsConfiguration Settings Label Print Server Settings To view the print server menu, complete this stepView and Modify Printer Settings PasswordTo view and modify printer settings, complete these steps View and Modify Printer SettingsGeneral Setup Serial Communications Setup Network Configuration Print Listings on Label Media Setup Calibration ZPL Control Advanced Setup Setting the Primary Network Print Server Primary Print ServerTo change the primary network, complete these steps TCP/IP Settings Network Configuration BBP81 4/BBP81 6 Web Page ShownTo change the TCP/IP settings, complete these steps TCP/IP Settings page opens TCP/IP Settings BBP81 4/BBP81 6 Web Page Shown Printer Controls To view Printer Controls, complete these stepsDirectory Listing To view the Directory Listing, complete these stepsAlert Setup Snmp USBSetting Alerts BradyConnect AlertsTo view Alert Setup using BradyConnect, complete these steps Alert Messaging System Establishing Email Alert Messaging Add Alert Message Click Add Alert Message Checking 10/100 Internal PS Configuration Settings BrowserPrint Server Settings Print Server Configuration Configuring the Print Server To change the TCP/IP Configuration, complete these stepsSending Email to Your Brady Printer To access POP3, complete these steps Print Server Configuration POP3 Printing Configuration BradyConnect WebView Hardware Troubleshooting Troubleshooting the 10/100 PS 10/100 Internal PS Network Status/Activity Indicator For the BBP81 4 and BBP81 6 printersUnable to Print To ping the printer, complete these stepsTelnet To open a telnet session on your PC, complete these stepsHardware Troubleshooting Print Protocols FTP Print Queues Configuring the Print Queue Berkeley Software Distribution BSD-Style Print QueueSystem V Queue Installation Spool Print Job ConfigurationPrerequisites Print Queues Frequently Asked Questions FAQsTCP Ports UDP PortsFrequently Asked Questions Frequently Asked Questions Glossary Glossary Glossary 100 Index LED 103 104 Page Brady Worldwide Inc