Siemens E-110-I user manual Appendix Specification, Software

Page 89

Appendix: Specification

Appendix: Specification

Software

ADSL Compliance

ANSI T1.413 Issue 2

ITU G.992.2 Annex A (G.lite)

ITU G.992.1 Annex A (G.dmt)

ITU G.992.1 Annex B (G.dmt)

ITU G.994.1 (G.hs)

ATM Features

Compliant to ATM Forum UNI 3.1 / 4.0 Permanent Virtual Circuits (PVCs)

Support up to 8 AAL5 Virtual Circuit Channels (VCCs) for UBR, CBR and GFR service classes

Provides ATM layer functionality

Provides adaptation layer (AAL5) functionality

Performs the traffic shaping and scheduling per ATM port

Supports PPP encapsulation over ATM (PPPoA) and PPP over Ethernet (PPPoE)

ADSL-aware CAC

Support for F5 AIS, RDI and loopback cells

Bridging Features

Up to 1000 hosts

Supports transparent bridging as specified in IEEE 802.1D Transparent Bridging

Supports bridged PDU encapsulation (RFC 2684)

MAC-level filter to accept/deny packets based on rules applicable at the MAC level

Routing Features

Network Address Translation (NAT)

IP filtering and raw filtering

Dynamic IP address allocation is supported through DHSP and IPCP

Point-to-point Protocol (PPP): PPPoA, PPPoE, PAP or CHAP for user authentication, Routing information Protocol (RIP) v1 and v2

Security Features

PAP (RFC1334), CHAP (RFC1994) for PPP session

Firewall support IP packets filtering based on IP address/Port number/Protocol type and TCP code field flags

Intrusion Detection provides protection from a number of attacks (such as SYN/FIN/RST Flood, Smurf, WinNuke, Echo Scan, Xmas Tree Scan, etc)

Configuration and Management

DSL Forum TR37-compliant auto configuration

SNMPv1 over DSL or Ethernet for access to the MIB-II (router only)

CLI (Command Line Interface) via serial interface or Telnet over Ethernet or DSL

Web-based Graphical User Interface (GUI) enabling end-user device configuration via Web browser

Update of boot image configuration data over TFTP/FTP

Rev:01_040220

83

Image 89
Contents Siemens Adsl E-110/E-110-I For Installation Safety NotesFor Using For ServiceIii ContentNAT Configuration Advanced Configuration via Web browserRIP Configuration Administration TasksAppendix Specification ContentsPage Before You Use FeaturesUnpacking Configuration and ManagementSystem Requirements Overview LED Indicators Front Panel System MessagesPhysical Outlook Front Panel9V 1A Rear PanelRear PanelEthernet Connecting the Adsl Router InstallationAnalog Pstn installation Choosing a place for the Adsl RouterIsdn NT Isdn installationInstall the USB driver USB driver installationClick Start Programs Siemens DSL Modem Uninstall Uninstall the USB driverFor Windows ConfigurationConfigure TCP/IP on Client PC Page Rev01040220 Page For Windows 98 and Windows 98 SE Your network interface card When returning to Network window, click OK Rev01040220 Page For Windows ME For Windows NT Page Page Page For Windows Page Page Click Internet ProtocolTCP/IP and then click OK For Windows XPFor Macintosh OS 8.6 From the Apple Menu, select System Preferences… For Macintosh OSClose the Network window Renew IP Address on Client PC For Windows ME For Windows Click Connect and Save Quick Configuration via Web browserInternet Access Advanced Configuration via Web browser Commonly Used Buttons and Icons Main MenuViewing Basic System Information Quick Configuration Committing Changes to Permanent Storage Rebooting the device using Configuration ManagerDSL Sub-MenusNAT Configuring IP Routes Advanced ConfigurationPart 1. Creating IP address pools Dhcp ConfigurationConfiguring Dhcp Server Part 2. Enabling Dhcp Server Mode Modifying Address Pools Part 3. Configuring your PCs as Dhcp clientsViewing Current Dhcp Address Assignments Select Lan Dhcp ServerPart 1. Defining the Dhcp relay interfaces Configuring Dhcp RelayPart 2. Enabling Dhcp relay mode These private IP addresses Are translated to NAT ConfigurationViewing Your NAT Configuration FieldDescription Page Field Description Viewing NAT Rules and Rule StatisticsViewing Current NAT Translations Adding NAT Rules Rdr rule Allowing external access to a LAN computer Basic rule Performing 11 translations Bimap rule Performing two-way translations Page Select a Send Mode and a Receive Mode RIP ConfigurationConfiguring the RIP Viewing RIP Statistics Firewall, IP Filters and Blocked Protocols Firewall ConfigurationField Description Max Half open TCP Conn Mail ID of Admin 1/2/3Max Icmp Conn Max Single Host ConnConfiguring IP Filter Global Settings IP Filter ConfigurationViewing Your IP Filter Configuration Field Description Rule ID Creating IP Filter RulesAction DirectionSecurity Level Field Description Log OptionLog Tag Start/End TimeTCP Flag Field Description Dest PortIcmp Type Icmp CodeSpecify Protocol eq TCP IP filter rule examplesViewing IP Filter Statistics Managing Current IP Filter Sessions To Block Specific ProtocolsUser Configuration Administration TasksChanging Your Login Password Changing the System Date and TimeAdding a New User Image UpgradeSelect Admin Local Image Upgrade Diagnostics View System AlarmsPort Settings View DSL Parameters Page Part 1 Configuring the Adsl Router Bridge ModeConnection Modes Creating an ATM VCC interfaceField Description VC Interface Creating an EoA interfaceMux Type Max Proto per AAL5Select Bridge LAN Config Enable Bridging functionLAN configuration Part 3 Configuring the PC PPP Connection ModePart 2 Check your connection status Commit your changesInterface Sec Type Select Public Creating a PPP interfaceSelect the ATM VC you created, e.g. aal5-0 Login Name Service NamePassword Field Description Status Select Start or StartOnDataRouter Connection Mode Creating a IPoA interface Problem Troubleshooting Suggestion LEDs TroubleshootingInternet Access Configuration Manager ProgramUpgrading Error Message Possible cause Action Problem Troubleshooting SuggestionGlossary RIP Routing Information Protocol PVC Permanent Virtual CircuitUDP User Datagram Protocol Virtual ServerSoftware Appendix SpecificationHardware Power Requirement and Operation Environment RequirementRegulatory Approvals and Compliance Physical