Siemens E-110-I user manual Configuration, Configure TCP/IP on Client PC, For Windows

Page 15

Chapter 3: Configuration

Chapter 3: Configuration

In order to access the Internet through the router, you must check the TCP/IP settings before configuring the router.

Step 1: Configure TCP/IP on Client PC

To access the ADSL Router via Ethernet, the host computer must meet the following requirements:

•With Ethernet network interface.

•Must have TCP/IP protocol installed.

•Set client PC with obtain an IP address automatically.

•With a Web browser installed: Internet Explorer 5.x or later.

The ADSL Router is configured with the default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. As the DHCP server is Enabled by default, the DHCP clients should be able to access the ADSL Router. Or you could assign an IP address to the host PC first for initial configuration.

You also can manage the ADSL Router through a Web browser-based manager: ADSL ROUTER CONTROL PANEL. The ADSL Router manager uses the HTTP protocol via a Web browser to allow you to set up and manage the device.

To configure the device via Web browser, at least one properly configured PC must be connected to the network (either connected directly or through an external hub/switch to the LAN port of the device).

If TCP/IP is not already installed, follow the steps below for installation.

For Windows 95

Note: Windows 95 users need the Windows 95 installation CD-ROMto complete the installation!

1.Click on the Start menu, point to Settings and click on Control Panel.

Rev:01_040220

9

Image 15

Contents Siemens Adsl E-110/E-110-I For Service Safety NotesFor Installation For UsingIii ContentAdministration Tasks Advanced Configuration via Web browserNAT Configuration RIP ConfigurationAppendix Specification ContentsPage Before You Use FeaturesConfiguration and Management System RequirementsUnpacking Front Panel LED Indicators Front Panel System MessagesOverview Physical OutlookRear PanelRear Panel Ethernet9V 1A Choosing a place for the Adsl Router InstallationConnecting the Adsl Router Analog Pstn installationIsdn NT Isdn installationInstall the USB driver USB driver installationClick Start Programs Siemens DSL Modem Uninstall Uninstall the USB driverConfiguration Configure TCP/IP on Client PCFor Windows Page Rev01040220 Page For Windows 98 and Windows 98 SE Your network interface card When returning to Network window, click OK Rev01040220 Page For Windows ME For Windows NT Page Page Page For Windows Page Page Click Internet ProtocolTCP/IP and then click OK For Windows XPFor Macintosh OS 8.6 From the Apple Menu, select System Preferences… For Macintosh OSClose the Network window Renew IP Address on Client PC For Windows ME For Windows Quick Configuration via Web browser Internet AccessClick Connect and Save Advanced Configuration via Web browser Commonly Used Buttons and Icons Main MenuViewing Basic System Information Quick Configuration Committing Changes to Permanent Storage Rebooting the device using Configuration ManagerDSL Sub-MenusNAT Configuring IP Routes Advanced ConfigurationDhcp Configuration Configuring Dhcp ServerPart 1. Creating IP address pools Part 2. Enabling Dhcp Server Mode Select Lan Dhcp Server Part 3. Configuring your PCs as Dhcp clientsModifying Address Pools Viewing Current Dhcp Address AssignmentsConfiguring Dhcp Relay Part 2. Enabling Dhcp relay modePart 1. Defining the Dhcp relay interfaces NAT Configuration Viewing Your NAT ConfigurationThese private IP addresses Are translated to FieldDescription Page Viewing NAT Rules and Rule Statistics Viewing Current NAT TranslationsField Description Adding NAT Rules Rdr rule Allowing external access to a LAN computer Basic rule Performing 11 translations Bimap rule Performing two-way translations Page RIP Configuration Configuring the RIPSelect a Send Mode and a Receive Mode Viewing RIP Statistics Firewall, IP Filters and Blocked Protocols Firewall ConfigurationMax Single Host Conn Mail ID of Admin 1/2/3Field Description Max Half open TCP Conn Max Icmp ConnIP Filter Configuration Viewing Your IP Filter ConfigurationConfiguring IP Filter Global Settings Direction Creating IP Filter RulesField Description Rule ID ActionStart/End Time Field Description Log OptionSecurity Level Log TagIcmp Code Field Description Dest PortTCP Flag Icmp TypeSpecify Protocol eq TCP IP filter rule examplesViewing IP Filter Statistics Managing Current IP Filter Sessions To Block Specific ProtocolsChanging the System Date and Time Administration TasksUser Configuration Changing Your Login PasswordImage Upgrade Select Admin Local Image UpgradeAdding a New User Diagnostics View System AlarmsPort Settings View DSL Parameters Page Creating an ATM VCC interface Bridge ModePart 1 Configuring the Adsl Router Connection ModesMax Proto per AAL5 Creating an EoA interfaceField Description VC Interface Mux TypeEnable Bridging function LAN configurationSelect Bridge LAN Config Commit your changes PPP Connection ModePart 3 Configuring the PC Part 2 Check your connection statusCreating a PPP interface Select the ATM VC you created, e.g. aal5-0Interface Sec Type Select Public Field Description Status Select Start or StartOnData Service NameLogin Name PasswordRouter Connection Mode Creating a IPoA interface Configuration Manager Program TroubleshootingProblem Troubleshooting Suggestion LEDs Internet AccessUpgrading Error Message Possible cause Action Problem Troubleshooting SuggestionGlossary Virtual Server PVC Permanent Virtual CircuitRIP Routing Information Protocol UDP User Datagram ProtocolSoftware Appendix SpecificationPhysical Power Requirement and Operation Environment RequirementHardware Regulatory Approvals and Compliance