Siemens 5935, 5930 manual Siemens

Page 50

SIEMENS 5930/5935 Business Gateway

Chapter 5 Advanced Setup

User’s Guide

QoS

 

 

5.In Source IP, select one of the following:

From/To: Enables source address checking. Specify the source IP address or range of IP addresses that must match for this policy to be used.

Do not care: Disables source address checking.

6.In Dest IP, select one of the following:

From/To: Enables destination address checking. Specify the destination IP address or range of IP addresses that must match for this policy to be used.

Do not care: Disables destination address checking.

7.In Protocol, select one of the following:

By number: Enter the protocol number to match in the protocol check.

Drop-down menu: Select the protocol to match in the protocol check (TCP or UDP).

Do not care: Disables protocol checking.

8.In Source Port, select one of the following:

From/To: Enter the source port or range of source ports to match in the source port check.

Drop-down menu: Select the application to match in the source port check.

Do not care: Disables source port checking.

9.In Destination Port, select one of the following:

From/To: Enter the destination port or range of destination ports to match in the destination port check.

Drop-down menu: Select the application to match in the destination port check.

Do not care: Disables destination port checking.

10.Select the priority to place on this policy if match criteria is met. This can be Normal, Low, Medium, or High. Normal is the default.

11.In Code Point - incoming and Code Point - outgoing, select one of the following:

Click the button next to the box to specify the Code Point. Be sure to enter the Code Point in the appropriate field.

Click Default to accept the default Code Point.

12.In Bidirection, select one of the following:

On: Enables bidirectional operation of the policy.

Off: Disables bidirectional operation of the policy.

13.In Start Time, specify the time of day when the policy becomes active.

14.In Duration, specify the time period for the policy to remain active.

15.In Repetition, select one of the following:

Always on: Policy is applied every day.

At: Policy is applied only one time on the specified month (MM), day (DD), and year (YY).

Every: Policy is applied on the specified day of the week.

16.Click Save.

SIEMENS

44

Image 50
Contents 5930/5935 Software License and Limited Warranty Software LicenseGeneral Provisions Table of Contents User Setup InstallationEasy Setup Advanced SetupSecurity Setup Monitoring RouterFront Panel for Back Panel forHardware Specifications for Software Specifications for PPP RFC SecurityFront Panel for Hardware Specifications for Software Specifications for IP Address Translation PC Requirements Installation RequirementsPackage Contents Network Service Provider Requirements Hardware Installation PC Configuration Windows 98/MEWindows NT Select TCP/IP Protocol from the Network Protocols listWindows Windows XP Mac OS Mac OSX Linux Configuring the Router Establish ConnectionRouter Information To do this Refer toAccess Easy Setup Wizard Select ProtocolNAT Enabled Bridging EnabledIP Routing Enabled Block Net Bios TrafficPoint-to-Point Protocol over Ethernet over PPPoA Point-to-Point Protocol over Ethernet over RFC1483 RFC RFC 1483 MAC Encapsulated Routing MER Dynamic Host Configuration Protocol Local Area Network Configuration User Setup User ManagementAdding/Modifying a User Account Deleting a User Account Radius User LookupLocal NoneUntrusted Secure Mode ConfigurationTrusted Configure the Radius Server Configure the TacPlus Server Management Classes Class Functional AreasChange Password Click Save and Reboot Access ControlNo access restrictions Telnet WebAdvanced Setup Router Clock Dhcp QoS Configure QoS Policy Siemens Before policy Reorder QoS PoliciesTo the end Routing Table Configuration Dial Backup Click Enable Dial BackupInternal Modem External Modem Switch Management Switch Mirror Configuration Switch Age Time ATM Traffic Shaping Non Real-Time Variable Bit Rate Constant Bit RateReal-Time Variable Bit Rate Unspecified Bit RateCommand Line Interface Security Setup NAT Port Number DisableDefault Snmp IP Filter Snmp PasswordEnter the New Password and New Password again Click Add IP RangeSecure Shell Key GeneratorConfigure SSH Load Keys Key Generator Firewall Scripts Stateful Firewall Firewall RulesConfigure Stateful Firewall View Dropped Packets Configure Firewall Rules Protocol/Port ApplicationDelete Firewall Rules IKE/IPSec Configuration Easy IKE/IPSec Setup Advanced IKE/IPSec Setup IKE PeersIKE Peers Definition IKE Proposals Definition IKE IPSec Proposals Definition Siemens IKE IPSec Policies Definition Siemens VPN Log On Monitoring Router System SummaryEthernet Interface Information Remote Connection InformationIP Routing Information System InformationDiagnostics PPPoE SessionInterface Information ATM StatisticsRouting Table Information Files InformationList All Configuration Data Memory UsageTCP/IP Statistics