Toshiba TDP-P7 Installation, Power Supply, Cleaning, Lamp Replacement, Fire and Shock Precautions

Page 4

IMPORTANT SAFETY INFORMATION

Important Safeguards

These safety instructions are to ensure the long life of the unit and to prevent fire and shock. Please read them carefully and heed all warnings.

Installation

For best results, use the unit in a darkened room.

Place the unit on a flat, level surface in a dry area away from dust and moisture.

Do not place the unit in direct sunlight, near heaters or heat radiating appliances.

Exposure to direct sunlight, smoke or steam can harm internal components.

Handle the unit carefully. Dropping or jarring can damage internal components.

Do not place heavy objects on top of the unit.

Power Supply

The unit is designed to operate on a power supply of 100 - 240 V 50/60 Hz AC. Ensure that your power supply fits these requirements before attempting to use the unit.

Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire.

Disconnect the power cable (main’s lead) from the power outlet after using the unit.

Before disconnecting the power cable, make sure that the STANDBY indicator lights in amber (not blinking or in green).

Cleaning

Disconnect the power cable (main’s lead) from the unit.

Clean the cabinet of the unit periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such as alcohol or thinner.

Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.

Clean the ventilation slots and speaker grills on the unit periodically using a vacuum cleaner. If accumulated dust blocks the ventilation slots, the unit will overheat, which may cause the unit to malfunction.

Use a soft brush attachment when using the vacuum cleaner. Do not use a hard attachment, such as a crevice tool, to prevent the damage to the unit.

Lamp Replacement

Be sure to replace the lamp when the Status indicator comes on. If you continue to use the lamp after 2000 hours of usage, the lamp will turn off.

Fire and Shock Precautions

Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the buildup of heat inside the unit. Allow at least 10 cm (4 inches) of space between the unit and walls.

Prevent foreign objects such as paper clips and bits of paper from falling into the unit. Do not attempt to retrieve any objects that fell into the unit. Do not insert any metal objects such as a wire or screwdriver into the unit. If something should fall into the unit, immediately disconnect the power cable from the unit and have the object removed by a qualified PLUS service person.

Do not place any liquids on top of the unit.

Carrying around

When carrying the unit around, please use the storage case that comes with it and, to protect the lens from scratches, always shut the Iris Lens Cover. Also, do not subject the unit to strong mechanical shock.

CAUTION – HOT!

The area around the exhaust vents is hot during and immediately after image projection. To avoid burns, keep your hands away from this area.

Wait until the exhaust vents area cools off before touching it.

Do not look into the lens while the unit is on. Serious damage to your eyes could result.

E-3

Image 4
Contents TDP-P7 Declaration of Conformity DOC Compliance NoticeThis label is located on the side of the remote control PrecautionsDo not look at the laser pointer’s light source Installation Power SupplyCleaning Lamp ReplacementMajor Features Table of Contents Table of Contents Checking the Supplied Accessories Names of the Main Unit Parts Built-in Security SlotZoom ring E-22 Built-in security slotRemote control sensor E-11 Names of the Main Unit PartsNames of Parts/Preparing the Remote Control Unit Names of the Remote Control PartsPreparing the Remote Control Remote Control RangeInserting the Batteries Side ViewProcedure Up to Projecting to the Screen Placement Guide Screen Size and Projection DistancePersonal computer RGB signal cable Supplied item Connections with Personal ComputerConnecting Personal Computers and Video Equipment To Output the External Output Signal of a Notebook ComputerManufacturer Model Key Connections with Composite Signals Video Equipment with Video ConnectorsVideo Equipment with S-VIDEO Connectors Video cable Mini DIN 4-pin plug Commercially availableConnections with Component Signals Connections with the Audio Jack Switch on the projector power OperatingPower Cable Connections and Switching the Power On/Off Press the Enter button to setThis completes the selection of the display language CursorFinishing Unplug the power cableButton on main unit Adjustment of the Projection Screen Adjustment of the Projection ScreenAdjust the projection image to the screen Zoom ringMaking Adjustments with the Adjusters Adjuster buttonFocus ring Raising the projection imageAutomatic Adjustment When Auto Source is OnWhen Auto Source is Off General OperationCancelling Video and Audio Temporarily Adjustment of the VolumePress the Cancel button to immediately close the display Freezing a Moving PictureImage can also be moved in the following circumstances Enlargement of the Image and Video MovementPress the Zoom button to enlarge the image Using the Presentation Timer Using the Laser Pointer OperationConnecting the computer and projector Click button on backJOG buttons Click buttonProtecting the Projector with the Security Lock Input the password using the number buttons 1 to Canceling the password/Changing the passwordCanceling the password Changing the passwordUsing the Quick Menu Content of Adjustments and SettingsPress the Select or button to adjust Example Brightness adjustment displayMenu Operation Method Names and Functions of Buttons Used for Menu OperationsAdjustment Bar and Settings Contents Menu Screen Names and FunctionsMenu Operation Method Menu Name Cursor Deep BluePerforming Menu Operations Menu Display Press the Menu button to display the menuMaking Adjustments/Settings Sub menuSelecting Another Menu Name with Remote Control Operation Color ViewOption Menu name Item Name Sub Menu SetupInfo Picture Adj. Picture Adjustment ImageBrightness / Contrast / Color / Tint / Sharpness Picture Adj. / Fine Picture / H Position / V PositionReset Fine PicturePosition ImageSelect the preset color mode ColorQuick Color Adj GammaSelection contents at the time of YPbPr input Color TempWhite Color SpaceWhite Balance Personal Computer Signal Video SignalsView AspectVertical Flip / Horizontal Flip KeystoneKeystone Save ViewAuto Power Off SetupAuto Source Lamp Mode SetupStatus Indicator Menu PositionPresentation Timer To start the timerInput Format Video and S-VideoOption LanguageOn Screen BackgroundSecurity Lock Startup ScreenOption Factory Default Lamp Timer ResetInfo StatusLamp Timer Resolution / FrequencyInfo When an Indicator is Lit or Flashing Thermal ProtectorTroubleshooting Check the following matters before requesting servicingCleaning Cleaning a Soiled Projector Main UnitCleaning the Inside of the Projector Dirty LensReplacing the Lamp Cartridge Replacing the Lamp Cartridge Remove the lamp cartridgeMount the new lamp cartridge Reset the Lamp TimerMount the lamp cover Specifications OpticalElectrical MechanicalResolution Frequency Video SignalTable of Supported Frequency Cabinet Dimensions