Toshiba TDP-P7 owner manual Replacing the Lamp Cartridge

Page 58

Replacing the Lamp Cartridge

•The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is about 2000 hours (when used in normal mode only). This could be shortened depending on conditions of use and other factors.

Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from test conditions at this company.)

•When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Please make the replacement following the procedure below.

•If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode and no longer turns on.

•Contact a store that sells the TDP-P7 for a replacement lamp. Indicate you need a TLP LP7 replacement lamp for the TDP-P7 (order code XX-XXX).

CAUTION

•Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop, disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will cause burns because of the high temperature.

•Do not remove any screws other than those specified.

•Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.

•If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer or the store the projector was purchased.

E-57

Image 58

Contents TDP-P7 Declaration of Conformity DOC Compliance NoticeThis label is located on the side of the remote control PrecautionsDo not look at the laser pointer’s light source Cleaning InstallationPower Supply Lamp ReplacementMajor Features Table of Contents Table of Contents Checking the Supplied Accessories Zoom ring E-22 Names of the Main Unit PartsBuilt-in Security Slot Built-in security slotRemote control sensor E-11 Names of the Main Unit PartsNames of Parts/Preparing the Remote Control Unit Names of the Remote Control PartsInserting the Batteries Preparing the Remote ControlRemote Control Range Side ViewProcedure Up to Projecting to the Screen Placement Guide Screen Size and Projection DistancePersonal computer RGB signal cable Supplied item Connections with Personal ComputerConnecting Personal Computers and Video Equipment To Output the External Output Signal of a Notebook ComputerManufacturer Model Key Video Equipment with S-VIDEO Connectors Connections with Composite SignalsVideo Equipment with Video Connectors Video cable Mini DIN 4-pin plug Commercially availableConnections with Component Signals Connections with the Audio Jack Switch on the projector power OperatingThis completes the selection of the display language Power Cable Connections and Switching the Power On/OffPress the Enter button to set CursorFinishing Unplug the power cableButton on main unit Adjust the projection image to the screen Adjustment of the Projection ScreenAdjustment of the Projection Screen Zoom ringFocus ring Making Adjustments with the AdjustersAdjuster button Raising the projection imageWhen Auto Source is Off Automatic AdjustmentWhen Auto Source is On General OperationPress the Cancel button to immediately close the display Cancelling Video and Audio TemporarilyAdjustment of the Volume Freezing a Moving PictureImage can also be moved in the following circumstances Enlargement of the Image and Video MovementPress the Zoom button to enlarge the image Using the Presentation Timer Using the Laser Pointer OperationJOG buttons Connecting the computer and projectorClick button on back Click buttonProtecting the Projector with the Security Lock Canceling the password Input the password using the number buttons 1 toCanceling the password/Changing the password Changing the passwordPress the Select or button to adjust Using the Quick MenuContent of Adjustments and Settings Example Brightness adjustment displayMenu Operation Method Names and Functions of Buttons Used for Menu OperationsMenu Operation Method Adjustment Bar and Settings ContentsMenu Screen Names and Functions Menu Name Cursor Deep BluePerforming Menu Operations Menu Display Press the Menu button to display the menuMaking Adjustments/Settings Sub menuSelecting Another Menu Name with Remote Control Operation Color ViewOption Menu name Item Name Sub Menu SetupInfo Brightness / Contrast / Color / Tint / Sharpness Picture Adj. Picture AdjustmentImage Picture Adj. / Fine Picture / H Position / V PositionPosition ResetFine Picture ImageQuick Color Adj Select the preset color modeColor GammaWhite Selection contents at the time of YPbPr inputColor Temp Color SpaceWhite Balance View Personal Computer SignalVideo Signals AspectKeystone Save Vertical Flip / Horizontal FlipKeystone ViewAuto Power Off SetupAuto Source Status Indicator Lamp ModeSetup Menu PositionInput Format Presentation TimerTo start the timer Video and S-VideoOn Screen OptionLanguage BackgroundSecurity Lock Startup ScreenOption Info Factory DefaultLamp Timer Reset StatusLamp Timer Resolution / FrequencyInfo When an Indicator is Lit or Flashing Thermal ProtectorTroubleshooting Check the following matters before requesting servicingCleaning the Inside of the Projector CleaningCleaning a Soiled Projector Main Unit Dirty LensReplacing the Lamp Cartridge Replacing the Lamp Cartridge Remove the lamp cartridgeMount the new lamp cartridge Reset the Lamp TimerMount the lamp cover Electrical SpecificationsOptical MechanicalResolution Frequency Video SignalTable of Supported Frequency Cabinet Dimensions