Toshiba TDP-MT700 owner manual Indicators, When the projector is in a normal state

Page 32

Indicators

There are three indicators which show the status of the projector. Check the following for information about the indicator lights. If there is anything wrong, turn the projector off and contact your dealer.

When the projector is in a normal state, ...

POWER

TEMP

LAMP

STATE

REMARK

 

 

 

 

 

Orange

 

 

Standby mode.

 

 

 

 

 

 

Flashing

 

 

The projector is powering up.

Cannot turn the projector off.

orange

 

 

 

 

 

 

 

 

 

 

 

Green

 

 

The projector is under normal

 

 

 

operation.

 

 

 

 

 

 

 

 

 

 

 

Off

Off

(1) The projector needs 110

 

 

seconds to cool down as it

 

 

 

 

 

 

 

 

was abnormally shut down

 

Flashing

 

 

without the normal cooling

Cannot turn the projector on.

green

 

 

down process. Or

 

 

 

 

 

 

(2) The projector needs to cool

 

 

 

 

for 110 seconds after the

 

 

 

 

power is turned off.

 

 

 

 

 

 

When the projector is in an abnormal state, ...

POWER

TEMP

LAMP

STATE

REMARK

 

 

 

 

 

 

 

 

(1) The lamp has exceeded its

Solution:

Orange

Off

Red

usage life. Or

• Install a new lamp.

(2) The lamp is not properly

• Please contact your dealer

 

 

 

 

 

 

attached or is damaged.

for assistance.

 

 

 

 

 

 

 

 

The dust filter is seriously clogged

Solution:

Orange

Red

Off

with dust. The projector is going to

• Install a new filter.

 

 

 

shut down.

 

 

 

 

 

Solution:

 

 

 

The internal temperature is too

• Make sure that the

 

 

 

ventilation holes are not

 

 

 

high.

 

 

 

blocked.

 

 

 

• The intake ventilation or the

 

 

 

• Relocate the projector.

Orange

Red

Off

exhaust ventilation is blocked.

• The projector may be in a

• Stop using the projector until

 

 

 

the ambient temperature

 

 

 

poorly ventilated location.

 

 

 

falls within the specified

 

 

 

• The ambient temperature

 

 

 

range. The maximum

 

 

 

may be too high.

 

 

 

operating temperature is

 

 

 

 

 

 

 

 

specified as 40°C / 104°F.

 

 

 

 

 

 

 

 

 

Solution:

 

 

 

 

• Check if the power supply is

Orange

Flashing

Flashing

The fans are not working.

stable.

red

red

• Check if there is object stuck

 

 

 

 

 

 

in the fans.

 

 

 

 

• Contact your dealer.

 

 

 

 

 

32 Additional information

Image 32
Contents TDP-MT700 Safety Precaution Model Name TDP-MT200Important Safety Instructions Cleaning Power-Cord ProtectionDo not use the product in a closed installa- tion state Water and MoistureAccessories Safety CheckDamage Requiring Service Stack InhibitedPower Supply Cord Selection Important PrecautionsImportant Precautions Exemption ClausesRemote Control Batteries Other Cautions and InformationContents Additional information Shipping contents OverviewConnector panel Projector exterior viewFront / Upper side Rear sideControl panel Remote controlControls and functions Picture Mode selection buttons p.23 Picture quality adjustment buttons p.26 PIP and POP buttonsInput buttons p Screen Size buttons p.27Positioning your projector Choosing a locationFloor in front of screen III. Floor at rear of screenObtaining a preferred projected image size Installation for a 169 ratio screenWidescreen ratio screen dimension table Inch Installation for a 43 ratio screenStandard ratio screen dimension table Connecting various equipment Connecting video inputsConnecting Hdmi devices Connecting component-video devicesConnecting a computer Connecting S-video or video devicesUsing the projector and remote control Turning the power onSwitching input signals PreparationsAdjust the image Adjusting the angle heightAuto-adjusting the image Fine-tuning the image size and clarityTheater Wide a 43 aspect ratio image is enlarged NON Other adjustmentsSelecting a Screen Size Personalizing the projector menu display Saving and loading the video memoryPausing the picture Turning the power offMenus Menu structureUsing the menus Picture menuExtended Picture Setting Display menuSetup menu Options menuAdvanced menu LampTo store Color Temperature to User 1 Replacing the lamp Contact your dealer for assistance Additional informationCare of the projector Loosen the screws on the lamp cover When the projector is in an abnormal state IndicatorsWhen the projector is in a normal state Troubleshooting Specifications Dimensions