Toshiba TDP-PX10 Important Precautions, Moisture Condensation, Place and Manner of Installation

Page 9

IMPORTANT PRECAUTIONS

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an extreme or sudden change in temperature to prevent the unit from possible damage.

Place and Manner of Installation

•Do not place in hot locations, such as near heating equipment. Doing so could cause malfunction, and shorten the life of the projector.

•Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening their lives, and darkening the screen.

•Do not use this product in the upright position or tilt it up or down by more than 20° from level. Doing so may cause a failure or shorten the life of the product.

•Using this instrument near a TV or radio may cause interference to the images or audio sound. If this happens, move it away from the TV or radio.

•Moving the projector from a low-temperature room to a high-temperature room may cause condensation on the lens or internal parts. If you continue to use it in that situation, it may malfunction. Wait until the condensation naturally disappears.

•In a high altitude location such as over 600m (2000ft) from sea level, the air is thin and cooling efficiency is reduced so use the projector with [Fan mode] set to [High]. Otherwise, surface of the projector become hot and the lifetime may be reduced. p.36

•Only plug the power cord into outlets rated for use with the power cord's specified voltage range. Do not overload extension cords or power strips as this can result in fire or electric shock.

•Route the power cable or the connecting cable away from where people could trip over it. The projector may fall, which could result in severe injury.

•Be sure the power cord is easily reached for unplugging in case of emergency. Do not place any obstacles near a wall outlet in which the cord is plugged.

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time, as they will leave marks on the finish. Do not use a chemically saturated cloth.

Before Using

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents TDP-PX10 Data Projector Model Name TDP-PX10!USA only Safety PrecautionsBefore Using Power Sources Important Safety InstructionsSource of Light VentilationCleaning Power cord protectionHeat Water and MoistureImportant Safety Instructions Damage Requiring Service AccessoriesService ServicingReplacement Parts Safety CheckDo not use the product in a closed installation location Place and Manner of Installation Important PrecautionsMoisture Condensation Avoid Volatile LiquidExemption Clauses Copyrights Other InformationDisposal TrademarksRemote Control Batteries Before Using Contents Others Before calling service personnelChecking the package contents Names of each part on the main unit Control panel Control panel Remote ControlPreparations Label locations Parts on the rear panel Service„ Loading dry-cell batteries into Remote control Preparing and using the remote control„ Operating the remote control Remove the battery coverDry-cell batteries Preparing and using the remote controlOperating a computer Connecting a computerPlacement Styles PlacementAs seen from above Projection Distance and SizeConnecting with computers ConnectionBefore connection Connecting with AV equipment Turning the power on and off „ Turning the power on Press the ON/STANDBY button„ Removing the lens cover „ Turning the power off Press the ON/STANDBY button PrecautionPress the ON/STANDBY button again Basic operations Using handy features Using auto setting For computer input onlyCorrecting the keystone distortion Using handy features „ Press the Freeze button on the remote controlFreezing the image Freeze How to use the menus Using the menusImage adjustment menu Using the menusDisplay effect Display setting menuLanguage Default setting menuDisplaying Information Status display File View Mode Using USB MemorySlideshow Mode / Display of movie files Using USB Memory Disconnecting USB memoryAbout USB memory function USB memory reset Backing up the dataFolders and files Lamp replacement „ When the lamp is brokenAbout lamp Lamp replacement Used Lamps Lens and main unit cleaning „ Lens cleaning„ Main unit cleaning LED Indicators State/ Problems Icon/ Messages Close Messages IndicatorsIf This Happens Check No power Before calling service personnelSpecifications „ List of general specifications„ Separately sold product Compatibility Resolution Sync KHz Sync Hz „ List of supported signals RGB signalsSpecifications „ List of supported signals Component signalsSignal Horizontal Frequency kHz Vertical Frequency Hz „ Pin assignment of S-VIDEO terminals „ Pin assignment of Computer in terminals
Top Page Image Contents