Toshiba B-480-QQ owner manual Media, Tag paper

2. SPECIFICATIONS

EO1-33008

2.4 Media

2.4	Media			Label			Refer to the following		Tag paper
							NOTE 2. Black Mark			Black Mark
		I					(on reverse side)			(on reverse side)
	Stop						Stop	I			Tag paper
	position
							position
						E	Cut			F
	Cut
	position						position		Reference
				Reference
		F			1		A		coordinate 1		A
			H	coordinate		B		H
				Reference					Reference
				coordinate	2				coordinate	2
				G			Feed direction		G
				D
							Fig. 2-1		C
				C
											[Unit: mm]
				Label dispensing mode						Cut mode
						Batch mode		Strip mode	Rotary cutter
	Item										Swing cutter
									Head-up is OFF	Head-up is ON
									3"/sec.:94.0	3"/sec.:38.0
					Min.		10.0	25.4	4"/sec.:98.0	4"/sec.:38.0	38.0
									5"/sec.:102.0	5"/sec.:38.0
				Label
									8"/sec.:113.0	8"/sec.:38.0
	A : Span of one label/tag				Max.				2730.0
									3"/sec.:30.0
					Min.		10.0	-	4"/sec.:30.0		25.4
				Tag					5"/sec.:30.0
									8"/sec.:38.0
					Max.		2730.0	-		2730.0

						3"/sec.:81.0(*1)	3"/sec.:25.0
		Min.	8.0	23.4		4"/sec.:85.0(*2)	4"/sec.:25.0	25.0 (*5)
B : Label/tag length
						5"/sec.:89.0(*3)	5"/sec.:25.0
						8"/sec.:100.0(*4)	8"/sec.:25.0
		Max.		2728.0			2724.0
C : Width including backing paper		Min.				50.8
		Max.				112.0
D : Label width		Min.				47.8
		Max.				109.0
E : Gap length		Min.		2.0			6.0
		Max.				20.0
F : Black mark length (Tag paper)		Min.				2.0
		Max.				10.0
G : Effective print width		Min.				10.0
		Max.				104.0 0.2
						3"/sec.:79.0	3"/sec.:23.0
		Min.	6.0		21.4	4"/sec.:83.0	4"/sec.:23.0	23.0
	Label					5"/sec.:87.0	5"/sec.:23.0
						8"/sec.:98.0	8"/sec.:23.0
H : Effective print length		Max.				2726.0
						3"/sec.:28.0
		Min.	8.0		-	4"/sec.:28.0		23.0
	Tag					5"/sec.:28.0
						8"/sec.:36.0
		Max.	2726.0		-		2726.0
I : Print speed up/slow down area						1.0
Thickness	Label
	Tag
Maximum effective length for	on the fly issue					1361.0
Outer roll diameter

NOTES: 1. The media specification other than above are unchanged.

2.The label length must be satisfied by the following conditions in each case.

(*1) When issuing a label using the rotary cutter, printing at a speed of 3"/sec., label length should be: 91.0mm - (Gap length/2) or more

(*2) When issuing a label using the rotary cutter, printing at a speed of 4"/sec., label length should be: 95.0mm - (Gap length/2) or more

(*3) When issuing a label using the rotary cutter, printing at a speed of 5"/sec., label length should be: 99.0mm - (Gap length/2) or more

(*4) When issuing a label using the rotary cutter, printing at a speed of 8"/sec., label length should be: 110.0mm - (Gap length/2) or more

(*5) When issuing a label using the swing cutter, label length should be: 35.0mm - (Gap length/2)

E2-3