Toshiba 431A operation manual Signal Words, Qualified Personnel

Page 11

2.2Signal Words

The signal words listed below are used throughout this manual. When the words DANGER, WARNING, CAUTION and ATTENTION are used in this manual they will include important safety information that must be carefully followed.

DANGER

The word DANGER in capital letters preceded by the safety alert symbol indicates that an imminently hazardous situation exists, and if not avoided will result in loss of life or serious injury to personnel.

WARNING

CAUTION

NOTICE

The word WARNING in capital letters preceded by the safety alert symbol indicates that a potentially hazardous situation exists, and if not avoided may result in loss of life or serious injury to personnel.

The word CAUTION in capital letters preceded by the safety alert symbol indicates that a potentially hazardous situation exists, and if not avoided may result in minor or moderate injury.

The word NOTICE in capital letters without the safety alert symbol indicates a potentially hazardous situation exists, and if not avoided may result in equipment and property damage.

2.3Qualified Personnel

Installation, operation, and maintenance shall be performed by Qualified Personnel Only. A Qualified Person is one who has the skills and knowledge relating to the construction, installation, operation, and maintenance of the electrical equipment and has received safety training on the hazards involved (Refer to the latest edition of NFPA 70E for additional safety requirements).

Qualified Personnel shall:

Have read the entire operation manual.

Be familiar with the construction and function of the UPS, the equipment being driven, and the hazards involved.

Be trained and authorized to safely energize, de-energize, ground, lockout/tagout circuits and equipment, and clear faults in accordance with established safety practices.

Be trained in the proper care and use of protective equipment such as safety shoes, rubber gloves, hard hats, safety glasses, face shields, flash clothing, etc., in accordance with established safety practices.

Be trained in rendering first aid.

For further information on workplace safety visit www.osha.gov.

4300 Series Ancillary Cabinets Installation and Operation Manual

3

Image 11
Contents Series Ancillary Cabinets Page Series Qualified Personnel only Product Use and Warranty RestrictionsUninterruptible Power System UPS Toshiba International Corporation PurposeToshiba Customer Support Center Toshiba Customer Support CenterContents 431M MBS Cabinet Installation Guide 11 431B Toshiba Battery CabinetToshiba Battery Cabinet w/ HX-205 431Bx000xxER111 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Qualified Personnel Signal WordsFactory Authorized Personnel Important Safety InstructionsMaximum Operating Temperatures Instructions Importantes Concernant LA Sécurité Battery SafetyDisclaimer Safety PrecautionsGeneral Maintenance Keep the area around the UPS cleanAvoid vibration or shock exceeding 0.5 g TransportingTransporting by Forklift Transporting By ForkliftInspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the ancillary cabinet in a controlled environment Conductor Routing and Grounding Metal Conduit is not AN Acceptable GroundFollow the torque criteria for tightening screws Wiring/ConnectionPerform wiring and connections with correct polarity Connect only one 1 ground wire to the earth ground terminalPage Storage Environment Operating PrecautionsStorage/Operating Environment Page Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Keep the Specified Clearance around the ancillary cabinets InstallationUPS Clearance Unpacking431A/431B 431M Anchor BoltsExample UPS Ground Bus Grounding WireSeries Overview 4300 Series System Assembly431B Batt. Cabinet Optional 4300 UPS431A 10 431A Toshiba Auxiliary CabinetAll cabinets are O’Brien Black Textured 431A AssembledAuxiliary Cabinet Warning Labels Alternative ConfigurationsCompression Fittings Bolt Tightening Specifications Torque431A with the 4300 UPS 431A with 431M and 4300 UPSOutput 431A Input/Output Power Cable Sizes431A Base Anchor Points Anchor the 431A CabinetSeries UPS Join the Auxiliary Cabinet with the UPS431A Series Join the 431A Cabinet with the 431M431M Toshiba Auxiliary Cabinet Outline Drawing 431B Door Open 11.1 431B Estimated Runtimes 11 431B Toshiba Battery Cabinet431B Door Closed 48082 4030841750 437844431B and 4300 UPS Place the 431B Cabinet Go to Section Place the 431B Cabinet 431B Power Cable Sizes431B Cable Access Plate Join the Battery Cabinet with the UPSSeries UPS 431B Wire the Battery Cabinet to the UPSComponent 431B Factory Supplied Shunt Trip Wiring 11.7 431B Backup Runtime TablesToshiba Battery Cabinet Outline Drawing 12 431B Door Closed 431B Door Open Toshiba Battery Cabinet w/ HX-205 431Bx000xxER111431B300017ER111, 4318500008ER111 12.1 431B Estimated Runtimes Battery Cabinet Mccb Detail69883 41750 Installation Safety Instruction 127 Adc 150 a Recommended/Maximum Wire size and Torque RequirementBattery Cab Sizes Lug Tightening TorqueJoin the Battery Cabinet with the UPS Wire the Battery Cabinet to the UPS 431B Typical Runtimes versus Load 12.7 431Bx000xxER111 Backup Runtime TablesToshiba Battery Cabinet HX-205 Schematic 10 Toshiba Battery Cabinet Outline Drawing 431M Door Closed 431M Door Open 13 431M MBS Cabinet Installation Guide13.1 431M Maintenance Bypass Switch MBS Options 431M Internal Arrangement 431M Cabinet Warning Labels Qualified Personnel only 431M with 431A and 4300 UPS 431M Input/Output Power Cable SizesSuggested Nema 2-Hole Compression Fittings Place the 431M Cabinet Locations/Dimension on UPS Base Upper Attach Points similarJoin the 431M Cabinet with the UPS PCB MBS Mechanical Interlock Plate Operation MBS Operation431M Cabinet Outline Drawing Purpose 14 431A MBS/PDU DistributionLoto Lock-Out Tag-Out Hasp 4400 MBS/PDU with Front Panels InstalledTools Required Optional Kickplate InstallationBox Contents Installing 4310-30/50-KP-AAttach the rear F/B Plate to the back of the UPS Slide Side Plates in along C-Channel baseAlign the F/B Plate with the UPS front Insert Side Plate tabs into F/B Plate slotsCompletion Side Kick Plate Plate F/B Kick Plates Back Side Similar Installing 4310-30/50-KP-BInstall the F/B Plates Move Side Plates to outer-most Channel baseElectrical Conduit Knock-out Data External Layouts/DimensionsDimensional Data Page Page Industrial Division