Toshiba 431A operation manual Optional Kickplate Installation, Box Contents, Tools Required

Page 71

15 Optional Kickplate Installation

Purpose

This Installation Guide shows how to correctly install the optional 4300 Series Kick Plates on the 4300 UPS, 431A Ancillary Cabinet, and the 431B Battery Cabinet. These instructions are also available in the Manuals for the respec- tive cabinets.

Toshiba International Corporation reserves the right, without prior notice, to update information, make product changes, or discontinue any product or service identified in this publication.

Toshiba International Corporation shall not be liable for direct, indirect, special, or consequential damages resulting from the use of the information contained within this Installation Guide.

Box Contents

Part Number

4310-30/50-KP-A

4310-30/50-KP-B

Instruction Sheet (P/N 66597)

1

1

F/B (Front/Back) Kick Plate, 22 in.

2

2

Side Kick Plate, 30.5 in.

2

(None)

NOTES

Initial set of kick plates to

Add-on kick plates to enclose ad-

 

enclose the base of one

ditional cabinets. The sides are

 

4300 cabinet.

moved to the outer sides outermost

 

 

cabinets in the lineup.

 

Both pair of kick plates are symmetrical - there is no upside

 

down.

 

Tools Required

None - The kick plates consist of the F/B panels that magnetically latch to the welded base of the 4300 Series cabi- nets and a second pair (sides) that magnetically latch to the F/B plates.

Installing 4310-30/50-KP-A

NOTE: Due to variations within manufacturing specifications, the spacing on the base channels may be slightly more or less than the separation between the magnetic

latches of the kick plates.

To correct this the installer should bend the magnetic latch support tab slightly to ensure a snug fit to the base channels.

STEP 1: Fit the F/B Plates with the UPS C-channel skids.

1.1Place a F/B kick plate on edge on the floor, magnetic latches side

toward the UPS with the magnetic latch faces facing left. See Figure 13-1.

1.2Place one in front and one at the back of the UPS.

1.3Slide the front F/B kick plate forward until both magnet latches adhere to the left and right vertical C-channel base skid member.

1.4If one of the magnets does not latch firmly, or the spacing is too nar- row, bend one or the other of the magnetic latch supports in or out as required to ensure a good fit. See Figure 13-1.

1.5Repeat Step 13-3 and 13-4 for the F/B kick plate at the back of the UPS.

1.6Remove the F/B kick plates from the C-channel base skids.

Left Base Skid

Right Base Skid

Figure 15-1

4300 Series Ancillary Cabinets Installation and Operation Manual

63

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Series Ancillary Cabinets Page Series Qualified Personnel only Product Use and Warranty RestrictionsUninterruptible Power System UPS Toshiba International Corporation PurposeToshiba Customer Support Center Toshiba Customer Support CenterContents 431M MBS Cabinet Installation Guide 11 431B Toshiba Battery CabinetToshiba Battery Cabinet w/ HX-205 431Bx000xxER111 Introduction Prohibited Symbol indicates do not take action General Safety InstructionsSymbols Qualified Personnel Signal WordsFactory Authorized Personnel Important Safety InstructionsMaximum Operating Temperatures Instructions Importantes Concernant LA Sécurité Battery SafetyDisclaimer Safety PrecautionsGeneral Maintenance Keep the area around the UPS cleanAvoid vibration or shock exceeding 0.5 g TransportingTransporting by Forklift Transporting By ForkliftInspection/Storage Keep the Specified Clearance around the UPS Installation PrecautionsInstall the ancillary cabinet in a controlled environment Conductor Routing and Grounding Metal Conduit is not AN Acceptable GroundFollow the torque criteria for tightening screws Wiring/ConnectionPerform wiring and connections with correct polarity Connect only one 1 ground wire to the earth ground terminalPage Storage Environment Operating PrecautionsStorage/Operating Environment Page Qualified Personnel shall Maintenance PrecautionsQualified Personnel only Keep the Specified Clearance around the ancillary cabinets InstallationUPS Clearance Unpacking431A/431B 431M Anchor BoltsExample UPS Ground Bus Grounding WireSeries Overview 4300 Series System Assembly431B Batt. Cabinet Optional 4300 UPS431A 10 431A Toshiba Auxiliary CabinetAll cabinets are O’Brien Black Textured 431A AssembledAuxiliary Cabinet Warning Labels Alternative ConfigurationsCompression Fittings Bolt Tightening Specifications Torque431A with the 4300 UPS 431A with 431M and 4300 UPSOutput 431A Input/Output Power Cable Sizes431A Base Anchor Points Anchor the 431A CabinetSeries UPS Join the Auxiliary Cabinet with the UPS431A Series Join the 431A Cabinet with the 431M431M Toshiba Auxiliary Cabinet Outline Drawing 431B Door Open 11.1 431B Estimated Runtimes 11 431B Toshiba Battery Cabinet431B Door Closed 48082 4030841750 437844431B and 4300 UPS Place the 431B Cabinet Go to Section Place the 431B Cabinet 431B Power Cable Sizes431B Cable Access Plate Join the Battery Cabinet with the UPSSeries UPS 431B Wire the Battery Cabinet to the UPSComponent 431B Factory Supplied Shunt Trip Wiring 11.7 431B Backup Runtime TablesToshiba Battery Cabinet Outline Drawing 12 431B Door Closed 431B Door Open Toshiba Battery Cabinet w/ HX-205 431Bx000xxER111431B300017ER111, 4318500008ER111 12.1 431B Estimated Runtimes Battery Cabinet Mccb Detail69883 41750 Installation Safety Instruction 127 Adc 150 a Recommended/Maximum Wire size and Torque RequirementBattery Cab Sizes Lug Tightening TorqueJoin the Battery Cabinet with the UPS Wire the Battery Cabinet to the UPS 431B Typical Runtimes versus Load 12.7 431Bx000xxER111 Backup Runtime TablesToshiba Battery Cabinet HX-205 Schematic 10 Toshiba Battery Cabinet Outline Drawing 431M Door Closed 431M Door Open 13 431M MBS Cabinet Installation Guide13.1 431M Maintenance Bypass Switch MBS Options 431M Internal Arrangement 431M Cabinet Warning Labels Qualified Personnel only 431M with 431A and 4300 UPS 431M Input/Output Power Cable SizesSuggested Nema 2-Hole Compression Fittings Place the 431M Cabinet Locations/Dimension on UPS Base Upper Attach Points similarJoin the 431M Cabinet with the UPS PCB MBS Mechanical Interlock Plate Operation MBS Operation 431M Cabinet Outline Drawing Purpose 14 431A MBS/PDU DistributionLoto Lock-Out Tag-Out Hasp 4400 MBS/PDU with Front Panels InstalledTools Required Optional Kickplate InstallationBox Contents Installing 4310-30/50-KP-AAttach the rear F/B Plate to the back of the UPS Slide Side Plates in along C-Channel baseAlign the F/B Plate with the UPS front Insert Side Plate tabs into F/B Plate slotsCompletion Side Kick Plate Plate F/B Kick Plates Back Side Similar Installing 4310-30/50-KP-BInstall the F/B Plates Move Side Plates to outer-most Channel baseElectrical Conduit Knock-out Data External Layouts/DimensionsDimensional Data Page Page Industrial Division
Top Page Image Contents