Siemens S7-300 Wiring the components, Preparing the cables, Cut the cables to the desired, length

Page 22

3.3 Wiring the components

3Installing and wiring the hardware

Warning

Dangerous electrical voltages!

Death or serious bodily injury and damage to machinery and equipment can occur if you do not observe the follow- ing safety precautions.

Before starting work, discon- nect the system and the device from the power supply.

18

3.3 Wiring the components

Wire the system components to the CPU 312C. This enables the CPU 312C to detect and evaluate the state of the components with the help of the control pro- gram.

•The momentary-contact switches are signal transmitters. You connect the sig- nal transmitters to the input terminals of the CPU 312C. The input terminals are labeled with “DI”.

•The motor is the signal receiver. You connect the signal receiver to the output terminals of the CPU 312C. The output terminals are labeled with “DO”.

The entire control loop is connected to the power supply via the CPU 312C.

Preparing the cables

1. Cut the cables to the desired	2. Remove the insulation and press
length.		the ferrules onto the ends of the
		cable.

SIMATIC S7-300 Getting Started for First Time Users Getting Started, 04/2007, 6ZB5310-0NC02-0BA0

Image 22

Contents SIMATIC S7-300 Getting Started for First Time Users 04/2007Order No. 6ZB5310-0NC02-0BA0 Danger Safety GuidelinesQualified Personnel Trademarks Prescribed UsageDisclaimer of Liability Page Contents 7 Congratulations1 Welcome To accomplish this, you will perform the following tasks Prerequisites 1 WelcomeValidity You will need a microQuantity Materials and toolsOrder number SiemensYou can also use the In addition, you will need the following componentsVDE 0805 / EN 60950 / IEC 950 or VDE 0106 Part Page 2 Preparing the PC Installing the driver for the PC Adapter USB Installing STEP 7 LiteOpen the installation file and follow the instructions 1. Open the dialog for setting the PG/PC interface Setting the interface2 Preparing the PC Page 2 Preparing the PC Page 3 Installing and wiring the hardware 3.1 What components are required? Installing and grounding the mounting rail 3.2 Installing the components3 Installing and wiring the hardware 2. Connect the mounting rail to the ground wire2. Install the CPU 312C Installing modules on the mounting rail1. Install the power supply, tighten ing the screws hand-tight1. Cut the cables to the desired 3.3 Wiring the componentsPreparing the cables 2. Remove the insulation and press2. Connect the power cable to the power supply Wiring the CPU 312C and the power supply1. Prepare the power cable 3. Secure the power cableWiring the momentary contact switches 1. Connect the momentary contact switches to the digital inputsWiring the motor 1. Connect the power supply for the digital inputs2. Wire the motor, if available. This step is optional Connecting the front panel connector Checking the line voltage setting 2. If necessary, change the switch position for the line voltage3.4 Commissioning the hardware Connecting the CPU 312C and the PC1. Connect the USB cable to the PC Adapter and your PC 2. Close the front panel Supplying power to the CPU 312C 1. Connect the supply cable to the supply system3 Installing and wiring the hardware 3. Set the main switch of the power supply to “ON” Testing the connections Page 4 Configuring the control in STEP 7 Lite 4.1 What is a STEP 7 Lite project? Opening the “conveyor” project 4 Configuring the control in STEP 7 Lite4.2 Opening a STEP 7 Lite project 1. Start STEP 7 LiteCreating the module configuration 4.3 Reproducing the module configuration in STEP 7 Lite1. Create a new S7-300 station 4 Configuring the control in STEP 7 Lite Page 4 Configuring the control in STEP 7 Lite Setting the parameters of the CPU 312C 1. Set the amount of retentive bit memory to “0”Saving the project 1. Save the project4.4 Establishing the online connection between the PC and CPU 312C Establishing the online connectionPerforming a memory reset on the CPU 312C 4.5 Downloading and checking the module configuration to the CPU 312C1. Delete the old program blocks and configurations from the CPU 312C Downloading the module configuration to the CPU 312C Checking the module configuration Page 5 Opening the program on the PC 5.1 What is a program? 5 Opening the program on the PC 5.2 Opening a program1. Open the program Page 6 Performing a test run 6.1 Downloading the project to the CPU 312C 6.2 Starting the test run 1. Set the mode switch of the CPU 312C to “RUN”6 Performing a test run 2. Press the green momentary con- tact switch to start the motor The output LED 0.5 lights up. The input LED 0.3 lights up The motor is switched offThe output LED 0.3 goes out Page 7 Congratulations Want to know more about SIMATIC S7-300? Contact us 8 Additional information 8.1 Diagnostics / correction of errors 8.2 Additional documentation 8 Additional informationName of manual DescriptionService & Support on the Internet 8.3 SIMATIC Technical SupportPage 8 Additional information

Related manuals

Manual 244 pages 25.52 Kb