Siemens manual Want to know more about SIMATIC S7-300? Contact us

Page 61
Want to know more about SIMATIC S7-300? Contact us.

With the completion of the test run, you have successfully performed the tasks in “S7-300 Getting Started - First Time User” and have created an executable con- trol for your plant.

If you wish, you can add to the control on your own and implement your own control tasks.

Want to know more about SIMATIC S7-300? Contact us.

Additional information is available through our Service & Support. Visit us on the Internet at:

http://www.siemens.com/automation/service

Additional addresses and contact information are provided on the following pages.

57

SIMATIC S7-300 Getting Started for First Time Users Getting Started, 04/2007, 6ZB5310-0NC02-0BA0

Page 60 Page 62
Image 61
Page 60 Page 62
Contents SIMATIC S7-300 Getting Started for First Time Users 04/2007Order No. 6ZB5310-0NC02-0BA0 Danger Safety GuidelinesQualified Personnel Trademarks Prescribed UsageDisclaimer of Liability Page 7 Congratulations Contents1 Welcome To accomplish this, you will perform the following tasks Validity 1 WelcomePrerequisites You will need a microOrder number Materials and toolsQuantity SiemensYou can also use the In addition, you will need the following componentsVDE 0805 / EN 60950 / IEC 950 or VDE 0106 Part Page 2 Preparing the PC Installing the driver for the PC Adapter USB Installing STEP 7 LiteOpen the installation file and follow the instructions 1. Open the dialog for setting the PG/PC interface Setting the interface2 Preparing the PC Page 2 Preparing the PC Page 3 Installing and wiring the hardware 3.1 What components are required? 3 Installing and wiring the hardware 3.2 Installing the componentsInstalling and grounding the mounting rail 2. Connect the mounting rail to the ground wire1. Install the power supply, tighten Installing modules on the mounting rail2. Install the CPU 312C ing the screws hand-tightPreparing the cables 3.3 Wiring the components1. Cut the cables to the desired 2. Remove the insulation and press1. Prepare the power cable Wiring the CPU 312C and the power supply2. Connect the power cable to the power supply 3. Secure the power cable1. Connect the momentary contact switches to the digital inputs Wiring the momentary contact switches1. Connect the power supply for the digital inputs Wiring the motor2. Wire the motor, if available. This step is optional Connecting the front panel connector 2. If necessary, change the switch position for the line voltage Checking the line voltage setting3.4 Commissioning the hardware Connecting the CPU 312C and the PC1. Connect the USB cable to the PC Adapter and your PC 2. Close the front panel 1. Connect the supply cable to the supply system Supplying power to the CPU 312C3 Installing and wiring the hardware 3. Set the main switch of the power supply to “ON” Testing the connections Page 4 Configuring the control in STEP 7 Lite 4.1 What is a STEP 7 Lite project? 4.2 Opening a STEP 7 Lite project 4 Configuring the control in STEP 7 LiteOpening the “conveyor” project 1. Start STEP 7 LiteCreating the module configuration 4.3 Reproducing the module configuration in STEP 7 Lite1. Create a new S7-300 station 4 Configuring the control in STEP 7 Lite Page 4 Configuring the control in STEP 7 Lite 1. Set the amount of retentive bit memory to “0” Setting the parameters of the CPU 312C1. Save the project Saving the projectEstablishing the online connection 4.4 Establishing the online connection between the PC and CPU 312CPerforming a memory reset on the CPU 312C 4.5 Downloading and checking the module configuration to the CPU 312C1. Delete the old program blocks and configurations from the CPU 312C Downloading the module configuration to the CPU 312C Checking the module configuration Page 5 Opening the program on the PC 5.1 What is a program? 5 Opening the program on the PC 5.2 Opening a program1. Open the program Page 6 Performing a test run 6.1 Downloading the project to the CPU 312C 6.2 Starting the test run 1. Set the mode switch of the CPU 312C to “RUN”6 Performing a test run 2. Press the green momentary con- tact switch to start the motor The output LED 0.5 lights up. The input LED 0.3 lights up The motor is switched offThe output LED 0.3 goes out Page 7 Congratulations Want to know more about SIMATIC S7-300? Contact us 8 Additional information 8.1 Diagnostics / correction of errors 8 Additional information 8.2 Additional documentationDescription Name of manual8.3 SIMATIC Technical Support Service & Support on the InternetPage 8 Additional information
Related manuals
Manual 244 pages 25.52 Kb
Top Page Image Contents