Toshiba 451C, 351C, e-STUDIO281c manual Subcode Area for the density to be adjusted

Page 36

2. Copier-specific Adjustments

(4) Enter adjustment mode [05]. Increase the value for code [648] to increase the copy density of text. (To improve faint, smudged text or thin lines)

•Initially, set a value larger than 180 for code 05-648. Copy and check the copy image quality. Next, finely adjust the value, in accordance with the original density. Up to 255 can be set for this code.

Original mode	[05] code	Value recommended	Acceptable value range	Default
Text/Photo	05-648	Approx. 180	0 to 255	30

After increasing the copy density, copy and check the copy image quality.

If further image quality adjustments are still necessary, use the next procedure.

(5) Press the [BASIC] button on the Control Panel. Select "TEXT" from among the original mode options.

*To have "TEXT" selected from among the original mode options by default, refer to procedure (1) in 2.8 To Eliminate Moiré.

After selecting Text mode, copy and check the copy image quality.

If further image quality adjustments are still necessary, use the next procedure.

(6) Enter adjustment mode [05]. Change the values for codes [590 to 592] to adjust the gamma curve balance of the medium- and high-density areas.

Original mode

[05] code

Subcode

Value recommended

Acceptable

Default

value range

Text/Photo

05-590

1/2

Set a value larger than 128.

0 to 255

128

Text

05-591

1/2

Photo

05-592

1/2

*Set the value in increments of approximately 20, while checking the copy image until the optimum value is obtained.

(Please be careful that the gradation (or density) of the medium-density area may exceed that of the high- density area, depending on the set value.)

*The subcode varies, according to the area for which the density is adjusted. Refer to the table below and set the subcode for the area to be adjusted. The density of light text or a graphic image will vary, if the medium- or high-density area is mainly adjusted. Setting "0" for the subcode allows you to adjust the low- density area. But it will not affect the light text or graphic images. Therefore, never change the value for

the low-density area.

Subcode	Area for the density to be adjusted
1	Medium-density area
2	High-density area

After adjusting the gamma curve balance, copy and check the copy image quality.

If further image quality adjustments are still necessary, use the next procedure.

2.1 e-STUDIO281c/351c/451c

Image 36

Contents File No. SME05001100 R05072188300-TTEC Ver002005-11 Toshiba TEC Corporation Revision Record Precautions in Servicing Purpose of the Imaging ManualIcons Table of Contents Printer-specific Adjustments Filing-specific AdjustmentsScanning-specific Adjustments Before the adjustment After the adjustment ‰ ProceduresTo Obtain a Darker Image ‰ ExplanationTo adjust the copy image quality To adjust the print image qualityPaper type Code Subcode Value Acceptable Default Paper type Acceptable paper weight‰ Cautions after the completion of the adjustment ‰ RemarksBefore the adjustment To Achieve the Image Quality Most Suitable for Paper Used‰ Explanation To Adjust the Blurred or Grained Image ‰ Cautions after the completion of the adjustment Plain paper Thick 05-293 60 to Plain paper Thick 05-1822 75 to Code Subcode Value recommended Acceptable Default ‰ Cautions after the completion of the adjustment To Minimize Variations in the Image Quality after Power-on ‰ Explanation After the adjustmentTo optimally program image quality control Invalid Before the adjustment After the adjustment Value for Difference in relative humidity Sheets default Value for‰ Cautions after the completion of the adjustment To Correct Out-of-Register Colors STUDIO3511/4511e-STUDIO281c/351c/451c‰ Procedure Procedure Code Test print pattern Printing PaperReferred SizeColor Code Subcode Value recommended Acceptable value range Correction at the leading edge Correction at the trailing edge05-69 Grid pattern for identifying out-of-register colors 05-64 Test print pattern 64 block pattern Correction at the leading/trailing edge ‰ Cautions after the completion of the adjustment Copier-specific Adjustments To Sharply Copy Light Text or Thin LinesTo Adjust the Copy Image Quality in Black Mode Original mode Code Value recommendedSubcode Area for the density to be adjusted Value Background peak Text peak To Adjust the Copy Image Quality in Full Color Mode ‰ Cautions after the completion of the adjustment To Adjust the Copy Image Quality in Auto Color Mode ‰ Cautions after the completion of the adjustment To Closely Match with the Color Balance of the Original ‰ Procedures 05-1779 Text 05-1780 Printed image 05-1781 Yellow ‰ Cautions after the completion of the adjustment To Improve the Reproducibility of Gray Subcode Area for the density to be adjusted To Copy in Vivid Colors Subcode Area for the density to be adjusted To improve the highlight reproducibility Photo Subcode Area for the density to be adjusted ‰ Cautions after the completion of the adjustment To Eliminate the Background Color Original Code Value recommended Acceptable Default Mode Fixed Varied Original mode Code Value recommended Acceptable Default 05-1691 Map 05-1692 ‰ Cautions after the completion of the adjustment After the adjustment To Adjust the Copy Image Quality in Black Mode Value Background peak Text peak Original mode Code Value recommended Acceptable Default To Adjust the Copy Image Quality in Full Color Mode ‰ Cautions after the completion of the adjustment To Eliminate Moiré To change default original mode on the Control Panel To change default original mode in setting modeValue for Default original mode at power-on 05-604 Set a value smaller than Text 05-605 ‰ Cautions after the completion of the adjustment To Copy Sharply To enhance sharpness 05-604 Set a value larger than Text 05-605 To Make Photo Edges Look Softer Copier-specific Adjustments Black Color mode Code Value recommended Acceptable Default Value Advantage of image qualityTo Make Solid Filled Bold Text Logo Highly Colored To Adjust the Copy Image Quality of a Black Logo Text 05-1795 Set a value larger than 128 Black To Adjust the Copy Image Quality of a Colored Logo Subcode Area for the density to be adjusted To Sharply Contrast the Hues of Highlighters on the Copy Code Mode to assign Acceptable Default Marker ColdSubcode Area for the density to be adjusted Paper mode Code Value recommended Acceptable value range DefaultTo Obtain a Good Color Balance on Thick Paper Nothing in particular To Obtain Smooth Gray-scale Photo Images ‰ Procedure To Change the Threshold in Auto Color Mode Threshold to be adjusted Code Acceptable To Clearly Copy Text To adjust the density of text Text/Photo 05-648 Approx To Adjust the Twin Color Copy Image Quality To adjust the image quality in red and black modeTo Adjust the Reproducibility of Black in Red and Black Mode To Adjust the Tint of Red in Red and Black ModeTo Adjust the Image Quality Scanned from the Radf Value Advantage of image quality Reproductivity Background Printer-specific Adjustments To Maintain a Steady Color BalancePrinter-specific Adjustments To Obtain the Desired Color Balance For Windows For Macintosh MenuText and graphics in this option PS3 Halftone Code Value AcceptableRecommended Image Quality Type Halftone option applied Windows Macintosh As viewed on the monitor Before the adjustment To Closely Match with the Color Balance on the Monitor‰ Procedure For Macintosh To Maintain a Uniform Gray Hue ‰ Procedure Quality Ö Pure Black & Gray For Windows Quality Ö Color Resolution Type ‰ Cautions after the completion of the adjustment To Easily Adjust the Overall Brightness ‰ Procedure To Easily Adjust the Overall Saturation ‰ Cautions after the completion of the adjustment To Clearly Print Light-colored Thin Lines or Text PCL5c PS3 For Macintosh To adjust the image quality in full-color printing PCL5c 600 x Detail 05-1030 1200 x 05-1038 Yellow To adjust the image quality in black-and-white printing Value Acceptable DefaultTo Clearly Print Thin Lines/Double Lines PCL5c PCL6 PS3 Printing Modes Ö Distinguish Thin Lines To Print in Toner Save Mode To Decrease the Image Density and Save TonerFor Windows Quality Ö Toner Save To Adjust the Image Density in Toner Save Mode Code Value recommended Acceptable Default Value range To Print Illegible Gray or Colored Text in Black ‰ Remarks To Ignore Blank Pages for Printing For Windows Printing Modes Ö Do not Print Blank Pages ‰ Cautions after the completion of the adjustment To Sharply Print Black Text For Windows For Macintosh PCL5c PCL6 PS3 PS3 Acceptable Default Adjusted ‰ Remarks To check the definition of black text Printer-specific Adjustments Filing-specific Adjustments To Clearly Store the B/W Image in Auto Color ModeFiling-specific Adjustments To Store the Original, while Reducing the File Size Ex. A4, 200 dpi, LOW = Approx KBTo change the default Jpeg compression rate To utilize the templateTo Store the Color Photo Image, while Minimizing Moiré To change default original mode on the Control Panel To change the density in Copy to Box ‰ Remarks To adjust the color balance in Print to Box To Match with the Color Balance on the OriginalPrint to Box PCL5c To Scan and Print, while Minimizing Moiré 05-1088 To Finely Print the Image Stored in the e-Filing box To Print Images Stored through Copy to Box or Print to BoxPrint to Box Scan to Box RGB data ‰ Explanation To Print Images Stored through Scan to Box Filing-specific4.Adjustments Scanning-specific Adjustments To Clearly Scan Text To reduce noise around textResolution File size ratio To Scan the Original, while Eliminating the Background Color To eliminate the background density05-1072 Gray scale 05-848 To Clearly Scan and Print the Original in Black and White To improve gradation and reduce graininess‰ Cautions after the completion of the adjustment To Scan the Original, while Reducing the File Size Scanning-specific Adjustments Original mode File size ratio Procedures used Possible image degradation‰ Remarks Image looks too soft and blurred 05-840 Text 05-841 To Scan the Original, while Enhancing Black ‰ Procedure To Scan the Original with the Desired Gradation Color mode Original mode Code Value recommended Acceptable Default Value range

Related manuals

Manual 106 pages 27.17 Kb

Manual 200 pages 20.21 Kb

Manual 372 pages 32.3 Kb