Toshiba 451C, 351C, e-STUDIO281c manual Code Subcode Value recommended Acceptable Default

Page 18

1. General Adjustments – Copying, Printing and e-Filing (Output from Box)

(2) Enter adjustment mode [05]. Change the value for code [434] to adjust the bottom margin.

*This adjustment will have an effect only on the image printed on the back of the paper (printed side delivered facing downwards) in duplex copying. Remember that it will not affect the image printed in simplex copying, the one printed on the front of the paper (printed side delivered facing upwards) in duplex copying, and the print image quality.

*In duplex copying, the bottom margin on the back of the paper may be narrower than on the front in simplex or duplex copying, depending on the paper size and how much paper is moistened. This results in the faint image at the trailing edge on the back of the paper. Adjust the bottom margin, in order to clearly copy at the trailing edge on the back of the paper.

• Use steps (a) to (b) to adjust the bottom margin.

(a)With the platen cover or RADF opened, make a double-sided copy. (Copy a solid black image.)

• Checking the copy image, determine how much the bottom margin should be increased.

*Select the best paper size for duplex copying, if necessary. It is recommended to use the paper, which is most frequently used for duplex copying.

*When making a double-sided copy of the solid black image, place blank paper on the original glass, allowing the solid black image to be copied only at the trailing edge on the back of the paper, for toner saving purposes.

(b)Enter adjustment mode [05]. Change the value for subcode "0" of code [434] to adjust the bottom margin on the back of the paper.

•The amount of change per step varies, depending on the paper size.

•Long size (A3/B4/LD/LG): The bottom margin will be increased by 0.042 mm per step.

•Short size (A4/LT): The bottom margin will be increased by 0.028 mm per step.

•Middle size (A4-R/LT-R, etc.): The bottom margin determined for the short size will be applied.

 

[05] code

 

 

Subcode

 

 

Value recommended

 

Acceptable

 

Default

 

 

 

 

 

 

 

value range

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Set a value larger than the current

 

 

UC: 28

05-434

 

0

 

 

0 to 255

 

EUR: 45

 

 

 

one to increase the bottom margin.

 

 

 

 

 

 

 

 

 

 

Others: 45

 

 

 

 

 

 

 

 

 

 

 

*Set the value in increments of approximately 12, while checking the copy image until the optimum value is obtained.

*Set "0" for the subcode. Setting "1" for the subcode allows you to adjust the right margin on the back in duplex copying, but it is not necessary here. Therefore, never change the value for subcode 1.

•After the adjustment, make a double-sided copy again, with the platen cover or RADF opened and check the image at the trailing edge on the back of the paper. If further image quality adjustments are still necessary, repeat step (b).

<Hint> If the user is concerned regarding the image quality at the trailing edge on the back of the paper, set a slightly wider bottom margin (3 to 4 mm). If not, it is recommended to set it to 2 to 3 mm.

1.2 e-STUDIO281c/351c/451c

Page 17 Page 19
Image 18
Page 17 Page 19
Contents File No. SME05001100 R05072188300-TTEC Ver002005-11 Toshiba TEC Corporation Revision Record Precautions in Servicing Purpose of the Imaging ManualIcons Table of Contents Printer-specific Adjustments Filing-specific AdjustmentsScanning-specific Adjustments To Obtain a Darker Image Before the adjustment After the adjustment‰ Procedures ‰ ExplanationTo adjust the copy image quality To adjust the print image qualityPaper type Code Subcode Value Acceptable Default Paper type Acceptable paper weight‰ Cautions after the completion of the adjustment ‰ RemarksBefore the adjustment To Achieve the Image Quality Most Suitable for Paper Used‰ Explanation To Adjust the Blurred or Grained Image ‰ Cautions after the completion of the adjustment Plain paper Thick 05-293 60 to Plain paper Thick 05-1822 75 to Code Subcode Value recommended Acceptable Default ‰ Cautions after the completion of the adjustment To Minimize Variations in the Image Quality after Power-on ‰ Explanation After the adjustmentTo optimally program image quality control Invalid Before the adjustment After the adjustment Value for Difference in relative humidity Sheets default Value for‰ Cautions after the completion of the adjustment To Correct Out-of-Register Colors STUDIO3511/4511e-STUDIO281c/351c/451cReferred ‰ ProcedureProcedure Code Test print pattern Printing Paper SizeColor Code Subcode Value recommended Acceptable value range Correction at the leading edge Correction at the trailing edge05-69 Grid pattern for identifying out-of-register colors 05-64 Test print pattern 64 block pattern Correction at the leading/trailing edge ‰ Cautions after the completion of the adjustment Copier-specific Adjustments To Sharply Copy Light Text or Thin LinesTo Adjust the Copy Image Quality in Black Mode Original mode Code Value recommendedSubcode Area for the density to be adjusted Value Background peak Text peak To Adjust the Copy Image Quality in Full Color Mode ‰ Cautions after the completion of the adjustment To Adjust the Copy Image Quality in Auto Color Mode ‰ Cautions after the completion of the adjustment To Closely Match with the Color Balance of the Original ‰ Procedures 05-1779 Text 05-1780 Printed image 05-1781 Yellow ‰ Cautions after the completion of the adjustment To Improve the Reproducibility of Gray Subcode Area for the density to be adjusted To Copy in Vivid Colors Subcode Area for the density to be adjusted To improve the highlight reproducibility Photo Subcode Area for the density to be adjusted ‰ Cautions after the completion of the adjustment To Eliminate the Background Color Original Code Value recommended Acceptable Default Mode Fixed Varied Original mode Code Value recommended Acceptable Default 05-1691 Map 05-1692 ‰ Cautions after the completion of the adjustment After the adjustment To Adjust the Copy Image Quality in Black Mode Value Background peak Text peak Original mode Code Value recommended Acceptable Default To Adjust the Copy Image Quality in Full Color Mode ‰ Cautions after the completion of the adjustment To Eliminate Moiré To change default original mode on the Control Panel To change default original mode in setting modeValue for Default original mode at power-on 05-604 Set a value smaller than Text 05-605 ‰ Cautions after the completion of the adjustment To Copy Sharply To enhance sharpness 05-604 Set a value larger than Text 05-605 To Make Photo Edges Look Softer Copier-specific Adjustments Black Color mode Code Value recommended Acceptable Default Value Advantage of image qualityTo Make Solid Filled Bold Text Logo Highly Colored To Adjust the Copy Image Quality of a Black Logo Text 05-1795 Set a value larger than 128 Black To Adjust the Copy Image Quality of a Colored Logo Subcode Area for the density to be adjusted To Sharply Contrast the Hues of Highlighters on the Copy Code Mode to assign Acceptable Default Marker ColdSubcode Area for the density to be adjusted Paper mode Code Value recommended Acceptable value range DefaultTo Obtain a Good Color Balance on Thick Paper Nothing in particular To Obtain Smooth Gray-scale Photo Images ‰ Procedure To Change the Threshold in Auto Color Mode Threshold to be adjusted Code Acceptable To Clearly Copy Text To adjust the density of text Text/Photo 05-648 Approx To Adjust the Twin Color Copy Image Quality To adjust the image quality in red and black modeTo Adjust the Reproducibility of Black in Red and Black Mode To Adjust the Tint of Red in Red and Black ModeTo Adjust the Image Quality Scanned from the Radf Value Advantage of image quality Reproductivity Background Printer-specific Adjustments To Maintain a Steady Color BalancePrinter-specific Adjustments To Obtain the Desired Color Balance For Windows For Macintosh MenuText and graphics in this option PS3 Halftone Code Value AcceptableRecommended Image Quality Type Halftone option applied Windows Macintosh As viewed on the monitor Before the adjustment To Closely Match with the Color Balance on the Monitor‰ Procedure For Macintosh To Maintain a Uniform Gray Hue ‰ Procedure Quality Ö Pure Black & Gray For Windows Quality Ö Color Resolution Type ‰ Cautions after the completion of the adjustment To Easily Adjust the Overall Brightness ‰ Procedure To Easily Adjust the Overall Saturation ‰ Cautions after the completion of the adjustment To Clearly Print Light-colored Thin Lines or Text PCL5c PS3 For Macintosh To adjust the image quality in full-color printing PCL5c 600 x Detail 05-1030 1200 x 05-1038 Yellow To adjust the image quality in black-and-white printing Value Acceptable DefaultTo Clearly Print Thin Lines/Double Lines PCL5c PCL6 PS3 Printing Modes Ö Distinguish Thin Lines To Print in Toner Save Mode To Decrease the Image Density and Save TonerFor Windows Quality Ö Toner Save To Adjust the Image Density in Toner Save Mode Code Value recommended Acceptable Default Value range To Print Illegible Gray or Colored Text in Black ‰ Remarks To Ignore Blank Pages for Printing For Windows Printing Modes Ö Do not Print Blank Pages ‰ Cautions after the completion of the adjustment To Sharply Print Black Text For Windows For Macintosh PCL5c PCL6 PS3 PS3 Acceptable Default Adjusted ‰ Remarks To check the definition of black text Printer-specific Adjustments Filing-specific Adjustments To Clearly Store the B/W Image in Auto Color ModeFiling-specific Adjustments To Store the Original, while Reducing the File Size Ex. A4, 200 dpi, LOW = Approx KBTo change the default Jpeg compression rate To utilize the templateTo Store the Color Photo Image, while Minimizing Moiré To change default original mode on the Control Panel To change the density in Copy to Box ‰ Remarks To adjust the color balance in Print to Box To Match with the Color Balance on the OriginalPrint to Box PCL5c To Scan and Print, while Minimizing Moiré 05-1088 To Finely Print the Image Stored in the e-Filing box To Print Images Stored through Copy to Box or Print to BoxPrint to Box Scan to Box RGB data ‰ Explanation To Print Images Stored through Scan to Box Filing-specific4.Adjustments Scanning-specific Adjustments To Clearly Scan Text To reduce noise around textResolution File size ratio To Scan the Original, while Eliminating the Background Color To eliminate the background density05-1072 Gray scale 05-848 To Clearly Scan and Print the Original in Black and White To improve gradation and reduce graininess‰ Cautions after the completion of the adjustment To Scan the Original, while Reducing the File Size Scanning-specific Adjustments Original mode File size ratio Procedures used Possible image degradation‰ Remarks Image looks too soft and blurred 05-840 Text 05-841 To Scan the Original, while Enhancing Black ‰ Procedure To Scan the Original with the Desired Gradation Color mode Original mode Code Value recommended Acceptable Default Value range
Related manuals
Manual 106 pages 27.17 Kb Manual 200 pages 20.21 Kb Manual 372 pages 32.3 Kb
Top Page Image Contents