Toshiba EN-2 user manual Initial Use, Adjusting the Video Settings Windows Vista Operations

Page 38

dynadock™

The DVI component additionally supports:

Resolution/

1600x1200

Color Depth

 

 

16 bit

60

 

 

32 bit

80

 

 

Note that interlaced modes are not supported.

Additional modes may be offered, depending upon the connected monitor, but these are not currently guaranteed.

If the monitor does not advertise the supported modes, the VGA or DVI component will choose a set of common screen modes.

If cloning the primary display, the VGA or DVI component will try to use the preferred monitor mode. In some cases, this may not be the most appropriate mode for the mirrored desktop. It is recommended that the primary display resolution be changed to closer match the default resolution of the dynadock monitor.

NOTE: For more information on supported modes, be sure to check the documentation supplied with your monitor.

Initial Use

When the VGA or DVI component first starts, it will mirror the primary monitor. Changes to the screen mode and VGA or DVI component operation mode can be made under the Windows display properties.

If no output is seen on the monitor connected to the VGA or DVI component, it may be in a mode which cannot be displayed by the monitor. This can happen if the monitor does not report its supported modes to the VGA or DVI component. Reduce the resolution of the primary display, and in turn the resolution of the VGA or DVI component display until an image is shown.

NOTE: Placing the monitor into an unsupported mode for long periods can damage it.

Adjusting the Video Settings - Windows Vista® Operations:

1.Position the mouse anywhere on your computer desktop, right-click and select Personalize, then click Display Settings.

2.To change the screen resolution or color quality, select those options on the screen. Be sure to select one of the supported resolutions and color quality numbers in the table above. For an external monitor, you can also select any resolution or color quality supported by that monitor.

3.To change the refresh rate, on the Display Settings screen, click Advanced Settings and then click Monitor.

4.Select a refresh rate from the Screen refresh rate pull down list. Be sure to select a refresh rate that is supported for the resolutions and color depth settings, as indicated in the table above. Then click OK.

5.Click OK to close the Display Settings screen.

EN-38

User’s Manual

Image 38
Contents User’s Manual Contents FCC notice Declaration of Conformity Information Regulatory ComplianceFCC Information FCC ConditionsWeee Information Safety InstructionsEU Declaration of Conformity Disclaimer PrecautionsCopyright Statement TrademarksPrecautions for Windows Vista only Introduction Features Front panelBack panel Package contents System RequirementsAssembly Sample Illustration The assembled dynadock Installation Installing the DriversSelect I Agree and click Next Sample Image Ready to Install screen Windows Vista Operations Click Finish when the dialog box shown below appears Windows XP Operations Install drivers Background Utility Program Connecting the dynadock to the Computer EN-22 User’s Manual Uninstalling the Utility UninstallingUninstalling Windows Vista Operations Uninstalling the Video Driver Uninstalling Windows XP Operations Uninstall the Audio DriverSample Illustration Remove Toshiba Video Dock USB 2.0 Ports Front and Back Panel Using the dynadockWindows XP, select Start Settings Network Connections Ethernet Port Back PanelSerial Port Back Panel Front Panel Audio Port Headphones or Speakers Front Panel Audio Port MicrophoneUsing the Virtual Speaker Shifter Controls Using the Basic Controls Digital S/PDIF Output Back panel Video Port VGA or DVI ConnectionVideo Modes Mirror ModeViewable screens Check the Extend my windows desktop onto this monitor box Extended ModeCheck the Extend the desktop onto this monitor box Uncheck the Extend my windows desktop onto this monitor box Switching from Extended Mode to Mirror ModeUncheck the Extend the desktop onto this monitor box Adjusting Video Settings Adjusting the Video Settings Windows Vista Operations Initial UseOther Devices Adjusting the Video Settings Windows XP OperationsExternal Monitors Disconnecting the dynadock Eject DockEject Dock and Sleep Opening Setting Dialog Eject by use of command lineRemoving Settings Setting Sleep Service Setting Message Notify Service Uncheck Show unexpected remove message boxSelect Audio Device Environmental Requirements SpecificationsPhysical Dimensions General Specifications Dynadock EN-48 User’s Manual