Dell 4691901 owner manual Physical Height Width Depth Weight, Environmental

Page 59

Controls and Lights

NOTE: You can test the health of the power system by pressing the test button. When the system power supply voltage is within specification, the self-test LED lights up. If the LED does not light up, the power supply may be defective. AC power must be connected during this test.

Power	Wattage	Maximum Heat	Voltage
		Dissipation

Mini-Tower	265 W	1390 BTU/hr	100 VAC to 240 VAC, 50 Hz to 60 Hz, 5.0 A
Desktop	250 W	1312 BTU/hr	100 VAC to 240 VAC, 50 Hz to 60 Hz, 4.4 A
Small Form Factor	240 W	1259 BTU/hr	100 VAC to 240 VAC, 50 Hz to 60 Hz, 3.6 A;
Coin-cell battery	3 V CR2032 lithium coin cell

NOTE: Heat dissipation is calculated by using the power supply wattage rating.

Physical	Height	Width	Depth	Weight

Mini-Tower	36.00 cm (14.17	17.50 cm (6.89 inches)	41.70 cm (16.42	8.87 kg (19.55 lb)
	inches)		inches)
Desktop	36.00 cm (14.17	10.20 cm (4.01 inches)	41.00 cm (16.14	7.56 kg (16.67 lb)
	inches)		inches)
Small Form Factor	29.00 cm (11.42	9.26 cm (3.65 inches)	31.20 cm (12.28	5.70 kg (12.57 lb)
	inches)		inches)

Environmental

Temperature range:

Operating	10 °C to 35 °C (50 °F to 95 °F)
Storage	–40 °C to 65 °C (–40 °F to 149 °F)
Relative humidity (maximum):
Operating	20% to 80% (non-condensing)
Storage	5% to 95% (non-condensing)
Maximum vibration:
Operating	0.26 GRMS
Storage	2.2 GRMS
Maximum shock:
Operating	40 G
Storage	105 G

59

Image 59

Contents Regulatory Model D07D Regulatory Type D07D001 Dell Inc Contents Troubleshooting System SetupContacting Dell SpecificationsPage Before Working Inside Your Computer Working on Your ComputerAfter Working Inside Your Computer Turning Off Your ComputerRelated Links Installing The CoverRemoving the Cover Removing the Expansion Card Installing The Front BezelRemoving the Front Bezel Page Removing the Optical Drive Installing The Expansion CardRemoving the Hard Drive Installing The Optical DrivePage Removing the Memory Installing The Hard DriveRemoving the Chassis Intrusion Switch Installing The MemoryRemoving The Speaker Installing The Chassis Intrusion SwitchInstalling The Speaker Removing The Heat Sink and Processor Installing The Heat Sink and Processor Removing The Power-Switch Cable Removing The Coin-Cell BatteryInstalling The Coin-Cell Battery Installing The Power-Switch Cable Removing The Front Thermal Sensor Removing The System Fan Installing The Front Thermal SensorInstalling The System Fan Removing The Input/Output Panel Installing The System FanRemove the Input/Output panel Installing The Input/Output PanelRemoving The Power Supply Disconnect the 4-pin power cable from the system boardPage Installing The Power Supply Remove the expansion cards Removing the System BoardRemove the system board from the chassis Installing the System BoardRemoving The PSU Thermal Sensor Installing The PSU Thermal Sensor CtrlAltF8 One-time boot and diagnostics utility menu F12 System SetupBoot Menu Boot Menu EnhancementsAction Keystroke Beep Codes and Text Error MessagesTiming Key Sequences NavigationSystem Setup Options Security Password Changes Password BypassPassword prompts during a system restart They are set. This option is disabled by defaultPerformance Power ManagementVirtualization Support Enable F12 Boot menu enabled by defaultMaintenance Post BehaviorSystem Logs Power Button Diagnostic LEDsDiagnostic Light Patterns Troubleshooting Steps Possible system board failure has occurred Re-seat the 2x2 power connector from the power supply unitPower Button Problem Description If the problem persists, the system board is faultyReinstalled all modules without error Problem Description Troubleshooting Steps Code Cause Microprocessor register failure Beep CodesCode Cause Code Cause DMA initialization failureCode Through Cause Code Cause Time-of-day clock stopped Error MessagesAddress mark not found Code Cause No time tick Shutdown failure Gate A20 failureData error Alert! Security override Jumper is installedBad command or file name Bad error-correction code ECC on disk readDiskette read failure Diskette subsystem reset failedHard-disk drive configuration error Diskette drive 0 seek failureKeyboard failure Invalid configuration information-please run Setup programInvalid Memory configuration, please populate DIMM1 Memory allocation errorNon-system disk or disk error No boot device availableNo boot sector on hard-disk drive No timer tick interruptTime-of-day not set-please run the System Setup program Read faultReset failed Seek error\ is not accessible. The device is not ready Unexpected interrupt in protected modeWrite fault Write fault on selected driveMemory SpecificationSystem Information ProcessorCards AudioNetwork Expansion BusAudio Back Panel Mini-Tower/Desktop External ConnectorsSystem Board Connectors Mini-Tower Two Desktop One Small Form FactorControls and Lights Environmental Physical Height Width Depth WeightPage Visit support.dell.com Contacting Dell