Dell 2100/200, 2100/180 manual Installing Drives in the External Bays, Configuring a Drive, Jumpers

Page 101

Chapter 8

Installing Drives in the External Bays

The external drive bays at the front of the computer (Figure 8-1) hold up to three user-accessible, half-height 5.25- or 3.5-inch devices—typically diskette, tape, CD-ROM, or digital audio tape (DAT) drives. Standard PowerEdge 2100 systems include a diskette drive in the top bay and a CD-ROM drive in the middle bay. A drive of your choice can be installed in the lower bay.

The diskette drive is controlled by the system board’s built-in diskette controller. The CD-ROM drive provided with the system and an additional small computer system interface (SCSI) drive (if installed in the lower bay) are controlled by the system board’s built-in SCSI controller.

NOTE: Dell PowerEdge 2100 systems support only SCSI hard-disk drives in the internal drive bays. For more information, see Chapter 9, “Installing Drives in the Internal Bays.”

Configuring a Drive

Because you may need to tailor a drive to work with your system, certain installation instructions in this chapter refer you to the documentation that came with the drive for information on changing jumper settings.

Jumpers

Drives installed by Dell are configured to work with your system. However, you should check the documentation for the drive to verify that the jumpers are set correctly for your particular configuration, and make any neces- sary alterations. (For an explanation of jumpers, see “Jumpers” in Appendix B.)

For example, when daisy-chaining two drives together, you may need to reconfigure one or both drives to differ- entiate between them for proper operation.

Installing Drives in the External Bays 8-101

Image 101
Contents USER’S Guide Page Ergonomic Computing Habits Safety InstructionsWhen Using Your Computer System Page Protecting Against Electrostatic Discharge When Working Inside Your ComputerPage About This Guide PrefaceNotational Conventions Warranty and Return Policy InformationOther Documents You May Need Example autoexec.bat and c\windows Typographical ConventionsPage Introduction System FeaturesDell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Supported Operating Systems Connecting External DevicesFront Panel Getting Help Preventing Unauthorized Access Inside the ComputerCD Main Menu Using the Dell Server Assistant CDBooting the CD Choose Language Configure the SystemRun System Utilities Use Online ManualsCreate Windows NT Server 3.51 Diskettes Create Operating System Support DiskettesCreate NetWare 4.x Diskettes Create NetWare 3.12 DiskettesVideo Drivers Installing Video Drivers for Windows NTAsset Tag Utility Restart Windows NTAssigning and Deleting an Asset Tag Number Using the Asset Tag UtilityAsset Tag Command-Line Options Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide SCSISelect Utility Installing and Configuring Scsi DriversScsi Select Default Settings Default Scsi Controller Settings Basic Host Adapter SettingsBoot Device Settings Advanced Host Adapter Settings Scsi Device SettingsStarting the SCSISelect Utility Using SCSISelect Menus Installation for Microsoft Win- dows NTUsing the Scsi Disk Utilities Installation OverviewPerforming a Windows NT 3.51 Installation Installing Windows NT 3.51 and the DriverPerforming a Windows NT 4.0 Installation Using Windows NT to Install or Update the DriverInstalling or Updating the Driver With Win- dows NT Removing a Host Adapter When you see the following message, click OK to exitSwapping a Host Adapter Restart your computerTroubleshooting for Windows NT Installation for Novell NetWareCalculating the Slot Number Installing EZ-SCSIPerforming a NetWare 4.x Installation Installing NetWare and the DriverLoad pathname aic7870.dsk options slot=x Performing a NetWare 3.12 InstallationLoad Command Line Options Using NetWare to Install or Update the DriverUsing the load Command Line Options Lunenable= Devenable=Tagdisable IocombineUsing Scsi Devices Sample load CommandBit Mask Options Load pathname aic7870 options slot=xUsing Removable Media Booting From a Scsi DeviceFiles Necessary to Set Up Booting From a Scsi Device Formatting MediaRead After Write Verify Options Using NetWare-Tested and -Approved DrivesDrive Status Items Optimizing Performance Using the NetWare Tape Backup UtilitySetting Up a CD-ROM Drive With Net- Ware 3.12 or Non-Host-Adapter Specific Troubleshooting for NetWareHost-Adapter Specific OffDell PowerEdge 2100/180 and 2100/200 Systems User’s Guide System Setup Screens Using the System Setup ProgramConfiguration Options and System Data Title BoxKey Functions System Setup KeysHelp Main Menu of the System Setup Program Entering the System Setup ProgramMain Menu Categories Boot Options Submenu Boot Options Submenu CategoriesNum Lock Service TagSpeaker MicroprocessorAdvanced Menu Categories Advanced Menu of the System Setup ProgramSerial Port Parallel ModeParallel Port Diskette ControllerSecurity Menu Categories Security Menu of the System Setup ProgramUser Password Is Supervisor Password IsSet Supervisor Password Set User PasswordVirus Check Reminder Exit Menu CategoriesUsing the Password Features Operating With a Supervisor Password Enabled Using Your Supervisor Password to Secure Your SystemDeleting or Changing an Existing Super- visor Password Using the User Password FeatureUsing Your User Password to Secure Your System Assigning a User PasswordDisabling a Forgotten Password Deleting or Changing an Existing User PasswordPassword Options Password OptionsResponding to Error Messages Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide System Board Options Using the Eisa Configuration UtilityConfiguring EISA, ISA, and PCI Expansion Cards When to Run the Eisa Configu- ration Utility How to Run the Eisa Configura- tion UtilityUsing Online Instructions Starting the Eisa Configuration UtilityMaking Selections in the Eisa Configu- ration Utility Configure Computer Learn About Configuring Your ComputerImportant Eisa Configuration Information Main MenuAdding an Expansion Card Add or Remove BoardsRepositioning an Expansion Card View or Edit DetailsDisplay the list of system board options as follows Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Eisa System Board Options Screen Example Advanced Menu Maintain System Configuration DisketteSet Date and Set Time Exit From This UtilityResolving Resource Conflicts Set Verification Mode MenuView Additional System Information Menu Maintain SCI Files MenuSystem Board Options Screen Modeling ModeHow Password Security Works Deleting an Existing Supervisor Password Assigning or Changing a Supervisor PasswordSelect the Supervisor Password category Type your new supervisor passwordDeleting an Existing User Password Assigning or Changing a User PasswordSelect the User Password category Type your new user passwordDisabling a Forgotten Password Before You Begin Safety First-For You and Your ComputerWorking Inside Your Computer Replacing the Computer Cover System OrientationRemoving the Computer Cover Replacing the Front Bezel Removing the Front BezelInside Your Computer Unpacking Your Hardware OptionWorking Inside Your Computer Inside the Chassis-Front/Right Side View Inside the Chassis-Back/Left Side View Removing the System Board Assembly Removing and Replacing the System Board AssemblyPartially remove the system board assembly from the chassis Disconnect the following cables from the system boardReconnect the cables to the system board Replacing the System Board AssemblyInstall the system board assembly in the chassis Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide System Board Features Installing System Board OptionsExpansion Card Examples Expansion CardsExpansion Slots Installing an Expansion CardRemoving an Expansion Card Installing an Expansion CardDIMMs and Dimm Sockets Adding MemoryDimm Installation Guidelines Memory Upgrade KitsInstalling System Board Options Sample Dimm Configurations Performing a Memory UpgradeInstalling a Dimm Removing a Dimm Installing a Microprocessor UpgradeUnpack the new microprocessor Remove the heat sinkRemove the microprocessor chip from the socket 10. Pin-1 Identification Install the microprocessor chip in the socket Fig- ureReplace the microprocessor securing clip 12. Installing the Heat SinkRemove the old battery Replacing the System BatteryInstall the new battery with the side labeled + fac- ing up Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Jumpers Installing Drives in the External BaysConfiguring a Drive External Drive Bay Hardware Removing Metal Inserts Removing and Replacing Front- Panel InsertsRemoving and Replacing Plastic Inserts Removing a Metal Insert Connecting the DriveDC Power Cables Installing Drives in the External BaysDiskette Drive Interface Cable Prepare the drive for installationVerify correct operation of your system Installing Scsi Drives in the External Bays10 -Pin to 50-Pin Adapter Configure the controller card if necessary11. Connecting an Optional Scsi Controller Card Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Scsi ID Numbers Installing Drives in the Internal BaysScsi Configuration Guidelines Scsi Termination Jumper Locations Device TerminationScsi Cable Configuring the Boot DeviceScsi Cable for a PowerEdge 2100 System Unpack each Scsi drive, and prepare it for installation Installing Scsi Hard-Disk Drives in the Internal BaysReinstall the hard-disk drive cage in the chassis Figure Install the Scsi drives in the hard-disk drive cageAttach the Scsi cable to each Scsi drive Test the Scsi drivesTable A-1. Technical Specifications Technical SpecificationsDrives Power Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Jumpers-A General Explanation Hardware Configuration FeaturesFigure B-1. System Board Jumpers Table B-1. System Board Jumpers Cardbios VGA EisaTable B-2. Connectors and Sockets on the System Board Connectors and SocketsSerial and Parallel Ports Ports and ConnectorsFigure B-3. Pin Numbers for the Serial Port Connectors Serial Port ConnectorsTable B-3. Pin Assignments for the Serial Port Connectors Parallel Port ConnectorKeyboard and Mouse Connectors Mouse Connector Keyboard ConnectorRED Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Backup Devices Scheduling BackupsRecovering Data Maintaining the SystemRecommended Tools and Accessories Cleaning System ComponentsCleaning the Computer, Monitor, and Keyboard Exteriors Cleaning DrivesEnvironmental Factors TemperatureHumidity AltitudeElectromagnetic and Radio Frequency Interference Dust and ParticlesCorrosion Shock and Vibration Power Source InterruptionsMagnetism Uninterruptible Power Supply Power Protection DevicesSurge Protectors Line ConditionersFCC Notices U.S. Only Regulatory NoticesClass a Class BCE Notice IC Notice Canada OnlyEN 55022 Compliance Czech Republic Only Class 2 Notice Vcci Notices Japan OnlyClass 1 Notice Korean Regulatory Notice Polish Center for Testing and Certification NoticeWymagania Polskiego Centrum Badañ i Certyfikacji Pozosta³e instrukcje bez pieczeñstwaRegulatory Notices D-141 Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Coverage During Year One Limited Three-Year Warranty U.S. OnlyWarranties and Return Policy General Limited Three-Year Warranty Canada OnlyCoverage During Years Two and Three Warranties and Return Policy E-145 Total Satisfaction Return Policy U.S. and Canada Only Table F-1. Technical Specifications Drives Technical Specifications F-149 Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Glossary BBS BiosBTU BZTCD-ROM CcftCGA CmosDIN DimmDIP DMAECC DTEECP EDOFCC FATGUI HMAIRQ IPXISA ITEMBR LUNMDA MGANMI NLMNtfs NvramPqfp PostPRN PVCRTC ROMScsi SdmsTSR TFTUMB UPSVGA VDSVesa Vram VlsiXMM XMS
Related manuals
Manual 73 pages 16.31 Kb

2100/180, 2100/200 specifications

The Dell 2100/200 and Dell 2100/180 are innovative offerings from Dell that cater to the demands of a variety of users, ranging from small businesses to larger enterprises. Both models are designed to deliver high performance and reliability, making them indispensable tools in the modern computing environment.

The Dell 2100/200 features an impressive Intel processor that ensures fast and efficient performance, making it suitable for multitasking and handling complex applications. Coupled with a generous RAM configuration, this model can easily manage demanding workloads, resulting in smoother performance and faster processing times. In contrast, the Dell 2100/180, while slightly less powerful, still maintains robust performance levels that are well-suited for general productivity tasks and everyday use.

Both models come equipped with ample storage options, featuring hard disk drives that provide significant space for data and application storage. Users can choose between traditional HDDs and solid-state drives (SSDs), allowing them to prioritize speed and performance based on their specific needs. The flexibility in storage options ensures that users can customize their systems according to their requirements, enhancing the overall user experience.

Connectivity is another area where the Dell 2100 series excels. Both models come with a range of ports including USB, HDMI, and Ethernet, allowing for seamless connectivity with various peripherals and networks. This versatility makes the machines ideal for environments where multiple devices need to be connected simultaneously, whether for presentations, data transfer, or internet access.

In terms of energy efficiency, both the Dell 2100/200 and Dell 2100/180 incorporate advanced cooling technologies that minimize energy consumption while maximizing performance. This not only helps reduce operational costs but also contributes to a more sustainable computing environment.

The design of these models is another distinguishing feature. With a compact form factor, they fit easily into office spaces while maintaining a professional appearance. Their durable build quality ensures longevity, making them a worthwhile investment for businesses.

Overall, the Dell 2100/200 and Dell 2100/180 serve as powerful and reliable machines that combine advanced technologies and user-centric designs. Whether for business or personal use, these models provide a solid foundation for effective computing, ensuring that users can achieve their goals efficiently and effectively.