Dell 2100/180 Basic Host Adapter Settings, Boot Device Settings, Default Scsi Controller Settings

Page 22

Table 3-1. Default SCSI Controller Settings

Setting

Default

 

 

SCSI Bus Interface Definitions:

 

Host Adapter SCSI ID

7

SCSI Parity Checking

Enabled

Host Adapter SCSI Termination

Low On/High

 

On

Boot Device Options:

 

Boot Target ID

0

Boot LUN Number

0

SCSI Device/Configuration:

 

Initiate Sync Negotiation

Yes (Enabled)

Maximum Sync Transfer Rate

40 Mb/sec

Enable Disconnection

Yes (Enabled)

Initiate Wide Negotiation

Yes (Enabled)

Send Start Unit Command

Yes (Enabled)

Advanced Host Adapter:

 

Host Adapter BIOS

Enabled

Support Removable Disks Under

Boot Only

BIOS as Fixed Disks

 

Extended BIOS Translation for

Enabled

DOS Drivers > 1 GB

 

Display <Ctrl><a> Message

Enabled

During BIOS Initialization

 

Multiple LUN Support

Disabled

BIOS Support for Bootable

Enabled

CD-ROM

 

BIOS Support for INT 13

Enabled

Extensions

 

Support for Ultra SCSI Speed

Enabled

NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary.

Basic Host Adapter Settings

The basic host adapter settings are the SCSISelect set- tings most likely to require modification.

Host Adapter SCSI ID. This option sets the host adapter’s SCSI ID. The default setting is SCSI ID 7, which allows the host adapter to support narrow SCSI devices in addition to wide SCSI devices. Dell recommends that you leave the host adapter set to SCSI ID 7.

SCSI Parity Checking. This option determines whether the host adapter verifies the accuracy of data transfer on the SCSI bus. The default setting is Enabled. You should disable SCSI Parity Checking if any SCSI device connected to the host adapter does not support SCSI parity; otherwise, leave it enabled. Most SCSI devices support SCSI parity. If you are unsure if a device supports SCSI parity, con- sult the documentation for the device.

Host Adapter SCSI Termination. This option sets ter- mination on the host adapter. The default setting for all Adaptec 78xx series host adapters is Low On/ High On. Dell recommends that you leave this option set to the default.

Boot Device Settings

The boot device settings allow you to specify the device from which to boot your computer.

Boot Target ID. This option specifies the SCSI ID of the device from which you wish to boot your system. The default setting is SCSI ID 0. The SCSI ID selected here must correspond to the ID configured on the boot device.

Boot LUN Number. If your boot device has multiple logical unit numbers (LUNs) and Multiple LUN Support is enabled (see “Advanced Host Adapter Settings” found later in this section), this option allows you to specify a particular LUN from which to boot on your boot device. The default setting is LUN 0.

3-22 Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide

Image 22
Contents USER’S Guide Page When Using Your Computer System Safety InstructionsErgonomic Computing Habits Page When Working Inside Your Computer Protecting Against Electrostatic DischargePage Preface About This GuideOther Documents You May Need Warranty and Return Policy InformationNotational Conventions Typographical Conventions Example autoexec.bat and c\windowsPage System Features IntroductionDell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Front Panel Connecting External DevicesSupported Operating Systems Preventing Unauthorized Access Inside the Computer Getting HelpBooting the CD Using the Dell Server Assistant CDCD Main Menu Run System Utilities Configure the SystemChoose Language Use Online ManualsCreate NetWare 4.x Diskettes Create Operating System Support DiskettesCreate Windows NT Server 3.51 Diskettes Create NetWare 3.12 DiskettesAsset Tag Utility Installing Video Drivers for Windows NTVideo Drivers Restart Windows NTAsset Tag Command-Line Options Using the Asset Tag UtilityAssigning and Deleting an Asset Tag Number Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Scsi Select Default Settings Installing and Configuring Scsi DriversSCSISelect Utility Boot Device Settings Basic Host Adapter SettingsDefault Scsi Controller Settings Scsi Device Settings Advanced Host Adapter SettingsStarting the SCSISelect Utility Using the Scsi Disk Utilities Installation for Microsoft Win- dows NTUsing SCSISelect Menus Installation OverviewPerforming a Windows NT 4.0 Installation Installing Windows NT 3.51 and the DriverPerforming a Windows NT 3.51 Installation Using Windows NT to Install or Update the DriverInstalling or Updating the Driver With Win- dows NT Swapping a Host Adapter When you see the following message, click OK to exitRemoving a Host Adapter Restart your computerInstallation for Novell NetWare Troubleshooting for Windows NTInstalling EZ-SCSI Calculating the Slot NumberInstalling NetWare and the Driver Performing a NetWare 4.x InstallationPerforming a NetWare 3.12 Installation Load pathname aic7870.dsk options slot=xUsing the load Command Line Options Using NetWare to Install or Update the DriverLoad Command Line Options Tagdisable Devenable=Lunenable= IocombineBit Mask Options Sample load CommandUsing Scsi Devices Load pathname aic7870 options slot=xFiles Necessary to Set Up Booting From a Scsi Device Booting From a Scsi DeviceUsing Removable Media Formatting MediaDrive Status Items Using NetWare-Tested and -Approved DrivesRead After Write Verify Options Setting Up a CD-ROM Drive With Net- Ware 3.12 or Using the NetWare Tape Backup UtilityOptimizing Performance Host-Adapter Specific Troubleshooting for NetWareNon-Host-Adapter Specific OffDell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Configuration Options and System Data Using the System Setup ProgramSystem Setup Screens Title BoxHelp System Setup KeysKey Functions Entering the System Setup Program Main Menu of the System Setup ProgramMain Menu Categories Boot Options Submenu Categories Boot Options SubmenuSpeaker Service TagNum Lock MicroprocessorAdvanced Menu of the System Setup Program Advanced Menu CategoriesParallel Port Parallel ModeSerial Port Diskette ControllerSecurity Menu of the System Setup Program Security Menu CategoriesSet Supervisor Password Supervisor Password IsUser Password Is Set User PasswordExit Menu Categories Virus Check ReminderUsing the Password Features Deleting or Changing an Existing Super- visor Password Using Your Supervisor Password to Secure Your SystemOperating With a Supervisor Password Enabled Using the User Password FeatureAssigning a User Password Using Your User Password to Secure Your SystemDeleting or Changing an Existing User Password Disabling a Forgotten PasswordPassword Options Password OptionsResponding to Error Messages Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Configuring EISA, ISA, and PCI Expansion Cards Using the Eisa Configuration UtilitySystem Board Options How to Run the Eisa Configura- tion Utility When to Run the Eisa Configu- ration UtilityMaking Selections in the Eisa Configu- ration Utility Starting the Eisa Configuration UtilityUsing Online Instructions Important Eisa Configuration Information Learn About Configuring Your ComputerConfigure Computer Main MenuAdd or Remove Boards Adding an Expansion CardView or Edit Details Repositioning an Expansion CardDisplay the list of system board options as follows Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Eisa System Board Options Screen Example Set Date and Set Time Maintain System Configuration DisketteAdvanced Menu Exit From This UtilityView Additional System Information Menu Set Verification Mode MenuResolving Resource Conflicts Maintain SCI Files MenuModeling Mode System Board Options ScreenHow Password Security Works Select the Supervisor Password category Assigning or Changing a Supervisor PasswordDeleting an Existing Supervisor Password Type your new supervisor passwordSelect the User Password category Assigning or Changing a User PasswordDeleting an Existing User Password Type your new user passwordDisabling a Forgotten Password Working Inside Your Computer Safety First-For You and Your ComputerBefore You Begin Removing the Computer Cover System OrientationReplacing the Computer Cover Removing the Front Bezel Replacing the Front BezelUnpacking Your Hardware Option Inside Your ComputerWorking Inside Your Computer Inside the Chassis-Front/Right Side View Inside the Chassis-Back/Left Side View Partially remove the system board assembly from the chassis Removing and Replacing the System Board AssemblyRemoving the System Board Assembly Disconnect the following cables from the system boardInstall the system board assembly in the chassis Replacing the System Board AssemblyReconnect the cables to the system board Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Installing System Board Options System Board FeaturesExpansion Cards Expansion Card ExamplesInstalling an Expansion Card Expansion SlotsInstalling an Expansion Card Removing an Expansion CardAdding Memory DIMMs and Dimm SocketsMemory Upgrade Kits Dimm Installation GuidelinesInstalling System Board Options Performing a Memory Upgrade Sample Dimm ConfigurationsInstalling a Dimm Installing a Microprocessor Upgrade Removing a DimmRemove the microprocessor chip from the socket Remove the heat sinkUnpack the new microprocessor Install the microprocessor chip in the socket Fig- ure 10. Pin-1 Identification12. Installing the Heat Sink Replace the microprocessor securing clipReplacing the System Battery Remove the old batteryInstall the new battery with the side labeled + fac- ing up Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Configuring a Drive Installing Drives in the External BaysJumpers External Drive Bay Hardware Removing and Replacing Plastic Inserts Removing and Replacing Front- Panel InsertsRemoving Metal Inserts Connecting the Drive Removing a Metal InsertInstalling Drives in the External Bays DC Power CablesPrepare the drive for installation Diskette Drive Interface CableInstalling Scsi Drives in the External Bays Verify correct operation of your systemConfigure the controller card if necessary 10 -Pin to 50-Pin Adapter11. Connecting an Optional Scsi Controller Card Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Scsi Configuration Guidelines Installing Drives in the Internal BaysScsi ID Numbers Device Termination Scsi Termination Jumper LocationsConfiguring the Boot Device Scsi CableScsi Cable for a PowerEdge 2100 System Installing Scsi Hard-Disk Drives in the Internal Bays Unpack each Scsi drive, and prepare it for installationAttach the Scsi cable to each Scsi drive Install the Scsi drives in the hard-disk drive cageReinstall the hard-disk drive cage in the chassis Figure Test the Scsi drivesTechnical Specifications Table A-1. Technical SpecificationsDrives Power Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Hardware Configuration Features Jumpers-A General ExplanationFigure B-1. System Board Jumpers Cardbios VGA Eisa Table B-1. System Board JumpersConnectors and Sockets Table B-2. Connectors and Sockets on the System BoardPorts and Connectors Serial and Parallel PortsSerial Port Connectors Figure B-3. Pin Numbers for the Serial Port ConnectorsKeyboard and Mouse Connectors Parallel Port ConnectorTable B-3. Pin Assignments for the Serial Port Connectors Keyboard Connector Mouse ConnectorRED Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Recovering Data Scheduling BackupsBackup Devices Maintaining the SystemCleaning the Computer, Monitor, and Keyboard Exteriors Cleaning System ComponentsRecommended Tools and Accessories Cleaning DrivesHumidity TemperatureEnvironmental Factors AltitudeCorrosion Dust and ParticlesElectromagnetic and Radio Frequency Interference Magnetism Power Source InterruptionsShock and Vibration Surge Protectors Power Protection DevicesUninterruptible Power Supply Line ConditionersClass a Regulatory NoticesFCC Notices U.S. Only Class BEN 55022 Compliance Czech Republic Only IC Notice Canada OnlyCE Notice Class 1 Notice Vcci Notices Japan OnlyClass 2 Notice Wymagania Polskiego Centrum Badañ i Certyfikacji Polish Center for Testing and Certification NoticeKorean Regulatory Notice Pozosta³e instrukcje bez pieczeñstwaRegulatory Notices D-141 Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Warranties and Return Policy Limited Three-Year Warranty U.S. OnlyCoverage During Year One Coverage During Years Two and Three Limited Three-Year Warranty Canada OnlyGeneral Warranties and Return Policy E-145 Total Satisfaction Return Policy U.S. and Canada Only Table F-1. Technical Specifications Drives Technical Specifications F-149 Dell PowerEdge 2100/180 and 2100/200 Systems User’s Guide Glossary BTU BiosBBS BZTCGA CcftCD-ROM CmosDIP DimmDIN DMAECP DTEECC EDOGUI FATFCC HMAISA IPXIRQ ITEMDA LUNMBR MGANtfs NLMNMI NvramPRN PostPqfp PVCScsi ROMRTC SdmsUMB TFTTSR UPSVesa VDSVGA XMM VlsiVram XMS
Related manuals
Manual 73 pages 16.31 Kb

2100/180, 2100/200 specifications

The Dell 2100/200 and Dell 2100/180 are innovative offerings from Dell that cater to the demands of a variety of users, ranging from small businesses to larger enterprises. Both models are designed to deliver high performance and reliability, making them indispensable tools in the modern computing environment.

The Dell 2100/200 features an impressive Intel processor that ensures fast and efficient performance, making it suitable for multitasking and handling complex applications. Coupled with a generous RAM configuration, this model can easily manage demanding workloads, resulting in smoother performance and faster processing times. In contrast, the Dell 2100/180, while slightly less powerful, still maintains robust performance levels that are well-suited for general productivity tasks and everyday use.

Both models come equipped with ample storage options, featuring hard disk drives that provide significant space for data and application storage. Users can choose between traditional HDDs and solid-state drives (SSDs), allowing them to prioritize speed and performance based on their specific needs. The flexibility in storage options ensures that users can customize their systems according to their requirements, enhancing the overall user experience.

Connectivity is another area where the Dell 2100 series excels. Both models come with a range of ports including USB, HDMI, and Ethernet, allowing for seamless connectivity with various peripherals and networks. This versatility makes the machines ideal for environments where multiple devices need to be connected simultaneously, whether for presentations, data transfer, or internet access.

In terms of energy efficiency, both the Dell 2100/200 and Dell 2100/180 incorporate advanced cooling technologies that minimize energy consumption while maximizing performance. This not only helps reduce operational costs but also contributes to a more sustainable computing environment.

The design of these models is another distinguishing feature. With a compact form factor, they fit easily into office spaces while maintaining a professional appearance. Their durable build quality ensures longevity, making them a worthwhile investment for businesses.

Overall, the Dell 2100/200 and Dell 2100/180 serve as powerful and reliable machines that combine advanced technologies and user-centric designs. Whether for business or personal use, these models provide a solid foundation for effective computing, ensuring that users can achieve their goals efficiently and effectively.