Mackie SP1200 user service Local MIC/LINE Input, Ambient MIC Input, Remote, RS485, Outputs

Page 17

PAGING MIC CONTROL

The PAGING MIC CONTROL connector is provided to connect a manual paging switch. Connect a normally-open switch between GND and ZONE A (to page in Zone A only), or GND and ALL CALL (to page over the entire system--if using multiple units). The voice-activated (VOX) control for the Paging Mic still operates in Zone A when the switch is off.

Local MIC/LINE Input

Connect a microphone to MIC/LINE INPUT A, using the supplied Phoenix-type connector, to use for a meeting room or other local speaking requirements. Set the PHANTOM and GAIN +40 dB switches to their appropriate positions.

Select the OFF button on the front panel. This disengages the selected Program Source and engages the MIC/LINE INPUT. Adjust the MASTER VOLUME up/down buttons so the meter level is at the “0” mark.

Note: The MASTER VOLUME setting for the MIC/LINE INPUT is independent of the MASTER VOLUME setting for INPUTS 1-4. The MASTER VOLUME setting for INPUTS 1-4 is stored in memory when the MIC/LINE INPUT is selected (the OFF button is engaged). When an INPUT 1-4 is selected, the MASTER VOLUME setting for the MIC/LINE INPUT is stored in memory.

Set the GAIN control so the meter indication is near the “0” mark when speaking at an average level into the microphone.

Set the 2-band EQ (LOW and HIGH) to the “U“ position. These can be adjusted later, if necessary.

AMBIENT MIC Input

This is an optional connection, but can greatly enhance the performance of the Paging Mic. Connect the optional MT-3100 mic to the AMBIENT MIC input. This provides an “ear” for the microprocessor to adjust the Paging Mic gain to compensate for the ambient noise level in the room. Use the supplied Phoenix-type connector to make these connections.

Note: Move the AMP ADDRESS switch #8 UP to enable the ambient mic. See page 19 for more information on "Using the Ambient Mic."

EXPANSION IN/OUT

If you are connecting two or more SP1200s in a system, use the EXPANSION IN/OUT connections to distribute the Program Input sources assigned to the Expansion Bus between SP1200s. The two 25- pin D-Sub connectors are in parallel (use one to connect to the previous SP1200 and one to connect to the next SP1200 in the chain).

Remote

You can connect one or more optional remote controls (up to 10) to the SP1200 to provide wall- mounted input select, program signal volume control, and local mic volume control.

RS485

A PC can be connected to the RS485 port to provide computer control using the SPLinker Sound Palette Control software application. If the PC doesn't have an RS485 serial port, you can either install an RS485 interface card, or use an RS232 serial port with an RS232-to-RS485 converter.

Two SP1200s can be controlled with one wired remote control by connecting the RS485 ports between the two SP1200s. Each amplifier must have the same AMP ADDRESS with one assigned as Master and the other as Slave. Use the supplied Phoenix-type connectors to make these connections.

Note: Move the AMP ADDRESS switch #6 DOWN for Master and UP for Slave.

PRE OUT/AMP IN

These connections can be used to insert a signal processor (i.e., graphic equalizer, compressor, etc.) into the signal chain, or to feed the signal to additional power amplifiers. If no external processor or external amplifier is to be used, leave the U-shaped jumper in place between the PRE OUT and AMP IN connectors.

Outputs

Use the supplied two-conductor Phoenix-type connector with appropriate speaker wiring to connect to the speaker or distributed speaker system.

SP1200 – 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Output Suitable For Class 2 Wiring PowerOL on Paging MICTable of Contents Safety InstructionsIntroduction Key FeaturesRear Panel Features Front Panel FeaturesRisk of Fire Replace with Same Type Fuse and Rating LOW High PriorityDo not Open Avis Risque DE Choc Electrique NE PAS Ouvrir Output SuitableTypical Monaural Application InstallationApplication Diagrams Program Inputs Paging MIC Multiple SP1200s-Multiple Zones-Shared SourcesLocal Inputs Paging Program EQExpansion Expansion OUT Output Expansion with Local MicExpansion Expansion OUT Port Comm Remote BUS Outputs Room Combining-ZonesRecord DirectApplications Tips on Installing and Using the SP1200-Plan AheadConnecting the Microphones Connecting the Program SourcesConnecting the Speakers ConnectionsConnecting the Remote Bus Connecting the Expansion BusBus Assign Internal SettingsConnecting the RS485 Serial Port EQ Bypass 70V/100V/8 Ohm SettingsVoltage Conversion AC Power ConsiderationsThermal Considerations Internal Switch and Jumper Settings External Switch SettingsOperation SP1200 Quick StartAmbient MIC Input Local MIC/LINE InputRemote RS485Using the 3-Band EQ Using InputsInput 1 and the Direct Output Input 4 PriorityUsing the Ambient Mic Using the Paging MicSetting the Gain Setting the VOX ThresholdAmbient Mic Calibration and Placement Using the Local MIC/LINE InputUsing the Remote Connection Using the PRE OUT/AMP ConnectionsUsing the RS485 Connection Zone a OutputUpgrading the Software Using the SPLinker Sound Palette ControllerUsing a 3rd Party Control System SP1200 Block Diagram SpecificationsPower Amplifier Section SP1200 SpecificationsAppendix a Default Settings Service InformationAppendix B Button Modes SP1200 Button Modes Press 2 on Power Up Ambient Mic Preamp MeteringAppendix C Voltage Conversion Mackie Industrial
Top Page Image Contents