Emerson XDF user manual Specifications, Physical specifications, Monitoring

Page 55

Specifications

12.0SPECIFICATIONS

Figure 36 XDF model numbers

Cooling

Input

Enclosure

Total Load

Model

Model Type

Capacity

Power

UPS

Monitoring

XDF

S

14

1

0

1

Liebert Extreme Heat

= 14kW

Density

Foundation Enclosure

1 = 120V-1ph-60HzkW

0 = None

and 208V-3ph-60Hz

1 = Module

S = Self-Contained,

Included

Air Cooled

W = Water Cooled

0 = None

G = PS1440RT2

A = GXT2-1000

H = PS2200RT2

B = GXT2-1500

I = PS3000RT2

C = GXT2-2000

K = GXT2-2700 (*)

D = GXT2-3000

L = GXT2-6000 (*)

E = GXT2-700

M = GXT2-10000 (*)

F = PS1000RT2

(*) 208VAC models

Condensate

Pump

0

0 = None

1 = Module

Included

Table 10 Physical specifications

	XDFS141		XDFW141
	Self- Contained,		Water/Glycol
Dimensions	Air Cooled XDF		Cooled XDF
Height, In. (mm)
Overall	82-1/4 (2089)		79-3/4 (2026)
Cabinet Only	79-3/4 (2026)		79-3/4 (2026)
Fan Guard	2-1/2 (57)		N/A
Equipment Rack Area	36U		42U
Width, In. (mm)
Overall	34-1/8 (867)
EIA Nominal	19 (483)
Inside Dimension	17-13/16 (452)
Depth, In. (mm)
Overall	49-1/2 (1257)
Mounting Depth, adjustable, minimum	24-3/8 (620)
Mounting Depth, adjustable, maximum	32-11/32 (821)
Weight, Lb. (kg)
Cabinet Only	710 (322)		668 (303)
Equipment Capacity	1200 (544)

49

Image 55

Contents Liebert XDF Page Table of Contents Cable Management Options Piping CONSIDERATIONS-WATER/GLYCOLMODELS onlyFilling the XDF with COOLANT-WATER or Glycol Electrical ConnectionsSpecifications MaintenanceTables Important Safety Instructions Indicates ground connection Glossary of SymbolsIndicates weight Hazardous Voltage PresentEntry Point Condenser Air ICOM Controller Backup Ventilation Air Intake CompressorCondenser Coil 1 Brazed Plate Condenser behind grille ICOM Controller Operational Overview Water/Glycol Cooled ModelReturn Line Female Condenser fanRemovable to reduce Height temporarilyDimensional data, self-contained, air cooled model Plate Connection 139.7mm176.5mm 47.6mmCable Entry Cutout 114mmEntry CutoutsDoors XDF ComponentsFrame EnclosureHeat Removal-Self-Contained, Air Cooled XDF Environmental ControlHeat Removal-Water/Glycol Cooled XDF Rear FrontBrazed Plate Condenser Liebert iCOM controller Control-Liebert’s iCOM ControllerClosed-Loop Water System Coolant Source-Water/Glycol ModelsWater/Glycol Return Line Cooled Drycooler LoopGeneral Enclosure Options Power Options MP Advanced Power Strips and ControllersUninterruptible Power Supply Optional EquipmentUnloading the XDF Recommended Setup EquipmentInstallation InspectionUnpack the XDF Handling the Unit While It is PackagedFork Lift Right front corner detail controls side of XDF Removing the XDF from SkidRoll XDF off the shipping skid 36 915mm XDF Site Preparation915mm Voltage Input Requirements Voltage RequirementsModel Feet m 60Hz 50Hz Drycooler Installation-Water/Glycol Cooled ModelOptional condensate pump performance Maximum HeadRecommended equipment arrangement Equipment LayoutRear-Mount Rails-Position Frame and Enclosure ConfigurationsMounting Hardware Internal Mounting RailsQuick Door Removal Door-RemoveSide Panels-Remove and Replace Remove the DoorReplace a Panel Remove the Right PanelWater supply flow rates GeneralClosed Loop Water System Piping CONSIDERATIONS-WATER/GLYCOL Models onlyCorrosion Protection Expansion Tanks, Fluid Relief Valves and Other DevicesFreeze Protection-Coolant Type and Insulation Glycol supply flow rates Glycol SolutionsDrycooler Loop System Ethylene glycol concentrationsFilling the XDF with COOLANT-WATER or Glycol XDF Water/Glycol Cooled Unit VolumeVolume in standard Type L copper piping Preparing the System for FillingCustomer Cable Entry Points Electrical ConnectionsDashed line delineates equipment compartment Rear Route Input Power Cables Through the XDF’s Top Utility Power SupplyCable Management Cable Management ConsiderationsCable Management Options Optional Cable Management Channel Cable AccessTop Cover and Back Cable Tray Detail View Startup XDF Startup Inspection ChecklistSite Conditions Escape Key Down Arrow Key Starting the XDFICOM Components and Functions Environmental ControlOperation Icon Key Name Function Keyboard icons and functionsOK no Navigating Through the iCOM DisplayEntering the Password Accessing Menus and Settings Viewing DataChanging Operational Settings Icon Name Description User menu iconsChanging the XDF’s Default Operating Temperature Changing iCOM’s Display SettingsHighlight the setting to be changed by pressing Enter Operation With the Door Open Uninterruptible Power Supply Backup Ventilation SystemXDF Compressor Maintenance Periodic MaintenanceTroubleshooting Monitoring SpecificationsPhysical specifications Self- Contained Water/Glycol Dimensions Air Cooled XDFTotal heat rejection Electrical specificationsSelf- Contained Water/Glycol Electrical Data Air Cooled XDF UPS performance data Optional Power SystemsTypes Quan Port Remote Monitoring and Control MP Advanced Power Strip specificationsRemote Monitoring Only Page That Ne tIti Ti n